Cat C32 Auxiliary/Generator Set Engine (EPA Tier 3)

Power Rating

Engine Specifications

Dimensions & Weights

AIR INLET SYSTEM

 Separate circuit after-cooled (SCAC)

 Air cleaner

 Turbocharger, jacket water cooled

 Turbocharger inlet, 152 mm (6 in) OD straight connection

CONTROL SYSTEM

 Programmable Low Idle (550 - 750 rpm)

 Programmable High Idle Limit for WOSR Ratings

 Electronic diagnostics and fault logging

 Engine and transmission monitoring (speed, temperature, pressure)

 Electronic fuel/air ratio control

 Engine Protection Mode for extended ambient conditions

 70-pin customer connector

 Throttle Input signal options

 0 - 5 Volts

 4 - 20 mA

 PWM (Pulse Width Modulated)

Programmable Low Idle (550 - 750 rpm)

Programmable High Idle Limit for WOSR Ratings

Electronic diagnostics and fault logging

Engine and transmission monitoring (speed, temperature, pressure)

Electronic fuel/air ratio control

Engine Protection Mode for extended ambient conditions

70-pin customer connector

Throttle Input signal options

0 - 5 Volts

4 - 20 mA

PWM (Pulse Width Modulated)

COOLING SYSTEM

 Separate Circuit After-Cooling (SCAC) for both HEX and Keel cooled engines

 Jacket Water (JW) and SCAC Heat Exchangers Shell & Tube for HEX cooled engines

 SCAC pump, gear driven

 Jacket water pump, gear driven

 Sea water pump, bronze impeller, gear driven, when selected for Hex cooled engines

 Sea water Pump & JW Heat Exchanger Connection: 76.2 mm (3in) ID Standard 4 Bolt ANSI Flange Connection

 Keel Connections: 76.2 mm (3in) ID Standard 4 Bolt

 SCAC and JW shunt tanks for maintaining proper pump inlet pressures

EXHAUST SYSTEM

 Water-cooled exhaust manifold & turbocharger

 4 Bolt 130 mm (5.12 in) diameter flanged outlet

Water-cooled exhaust manifold & turbocharger

4 Bolt 130 mm (5.12 in) diameter flanged outlet

FLYWHEELS & FLYWHEEL HOUSINGS

 SAE standard rotation (CCW facing exciter end)

 Flywheel Housing: SAE No. 0, Flywheel: 18 inch, 136 teeth

SAE standard rotation (CCW facing exciter end)

Flywheel Housing: SAE No. 0, Flywheel: 18 inch, 136 teeth

FUEL SYSTEM

 Duplex Fuel Filters, Spin-on, RH & LH service

 Fuel connections size: r driven

 Plate-type fuel cooler installed behind Aftercooler Shunt Tank

 Fuel transfer pump, gear driven

 Manual fuel priming pump

 Hybrid fuel line design

LUBE SYSTEM

 Simplex Oil Filters, RH or LH service

 Deep sump oil pan

 RH or LH service oil filler locations

 RH or LH service dipstick

 Oil pump, gear driven

MOUNTING SYSTEM

 Front support - 33 inches wide

POWER TAKE-OFFS

 Front Poly-V groove pulley (Quantity 1) for auxiliary drives

GENERAL

 Common electrical bonding point

 Engine does not ship with zinc components

EXHAUST SYSTEM

 Dry Elbows

 Flexible Fitting

 Flange

 Muffler

 Muffler Spark Arresting

Dry Elbows

Flexible Fitting

Flange

Muffler

Muffler Spark Arresting

AIR INLET SYSTEM

 Air Inlet Adapter

Air Inlet Adapter

CHARGING SYSTEM

 Battery Chargers

 Charging Alternators

 Ammeter

Battery Chargers

Charging Alternators

Ammeter

CONTROL SYSTEM

 Load Sharing Attachment

 Instrument Panels

 Caterpillar Alarm Protection

 Fuel and Oil Shielding

FUEL SYSTEM

 Water Separator

GENERAL

 FUMES DISPOSAL SYSTEM

FUMES DISPOSAL SYSTEM

INSTRUMENTATION

 Instrument Panels

 OEM Wiring Harness

 Engine to Engine Harness

 Gauges

 Transmission Sensors

 Exhaust Temperature Sensors

LUBE SYSTEM

 Duplex Oil Filters

 Sump Pump

POWER TAKE-OFFS

 Rear Hydraulic Pump Drive

Rear Hydraulic Pump Drive

STARTING SYSTEM

 Electric Starting Motors - Single 24 Volt

 Air Starting Motor

 Dual Starting Motors (Electric and Air)

 Air Start Accessories

 Starting Aids - JW Heaters

 Battery Sets - 24 Volt - Dry

MOUNTING SYSTEM

 Front Support

 Rear Support

 Isolators Mounts

 Adapter Kits

Front Support

Rear Support

Isolators Mounts

Adapter Kits

PACKING

 Engine Protective Cover

 Storage Preservation

 Export Packing

Engine Protective Cover

Storage Preservation

Export Packing