C175-16 Generator Set
Diesel Generator Sets
-
Specification Summary
- Standby Rating 3100(no fan)/3000 kVA
- Prime Power Rating 2825(no fan)/2725 kVA
- Emissions/Fuel Strategy Low Fuel, Low Emissions
- Voltage 380 to 11000 Volts
- Download Brochure
Generator Set Specifications
| Standby Rating | 3100(no fan)/3000 kVA |
| Prime Power Rating | 2825(no fan)/2725 kVA |
| Emissions/Fuel Strategy | Low Fuel, Low Emissions |
| Voltage | 380 to 11000 Volts |
| Frequency | 50 Hz |
| Speed | 1500 rpm |
| Duty Cycle | Standby, Mission Critical, Prime, Continuous |
| Maximum Rating | 3100 kVA |
| Minimum Rating | 2500 kVA |
Engine Specifications
| Engine Model | C175-16 SCAC, V-16, 4-Stroke Water-Cooled Diesel |
| Bore | 175 mm |
| Stroke | 220 mm |
| Displacement | 84.7 l |
| Compression Ratio | 16.7:1 |
| Aspiration | Turbo Aftercooled |
| Fuel System | Common Rail |
| Governor Type | ADEM� A4 |
Generator Set Dimensions
| Length - Minimum | 6137 mm |
| Length - Maximum | 7900 mm |
| Width - Minimum | 2110 mm |
| Width - Maximum | 2786 mm |
| Height - Minimum | 2211 mm |
| Height - Maximum | 3307 mm |
| Dry Weight - Genset (minimum) | 19391 kg |
| Dry Weight - Genset (maximum) | 23020 kg |
Air Inlet
Air Cleaner
Air Cleaner
4 x Single element canister with service indicator(s)
EMCP 4.2B
Volts (L-L & L-N)
Engine cycle crank
Power Factor (per phase & average)
Overcurrent
Communications
Emergency stop
2 Programmable relay outputs (Form C)
6 Programmable digital inputs
2 Programmable digital outputs
Environmental sealed front face.
DC Volts
Reverse power
Programmable Protective Relaying Functions
High coolant temperature
Accessory module data link
Low coolant level
Over / under frequency
Amps (per phase & average)
True RMS AC metering, 3-phase, +/-2% accuracy
Low coolant temperature
Reverse Reactive Power
Controls
Oil pressure (psi, kPa or bar)
Lamp test
Coolant temperature
Warning / shutdown Indicators
4 Programmable relay outputs (Form A)
Alarm acknowledge
Generator phase sequence
24 Volt DC operation
Serial annunciator module data link
Customer data link (Modbus RTU)
Failure to start (overcrank)
Auto / start / stop control.
Low oil pressure
RPM
Text alarm / event descriptions.
Digital Indicators
Generator mounted - rear facing
Emergency stop pushbutton
Engine cool-down timer.
Operating hours
Over / under voltage
Overspeed
Frequency (Hz)
Radiator group - shipped loose
SCAC cooling
Coolant Sensors
Coolant drain line and valves
Fan and belt guards
Bolted flange, with bellow for each turbo
Dry Exhaust Manifold
Filters x 3
Secondary / Tertiary fuel filters
10 Micron Spin On Type
4 Micron Spin On Type
Primary fuel filter water / fuel water separator
Engine mounted filters X3
6 Leads
IEC platinum stator RTDs
Voltage regulator
Reactive droop capability
3 Phase voltage sensing
RFI suppression
Min / max exciter limiter
exciter diode monitor
Form Wound
Permanent magnet
NEMA Class H insulation
Class H temperature rise at 40C ambient
(LV) Busbar connections, top/center mounted, top cable entry
3 Phase Brushless
Salient pole
50 Hz models: IEC standard hole pattern
(MV) Busbar connections, right side extension box, bottom cable entry
Anti condensation space heater
Class F temperature rise at 40C ambient
Right side extension box, bottom cable entry
ADEM A4
Redundant shutdown (Overspeed protection through a duplicate speed sensing system)
Gear type lube oil pump
Lubricating oil
Fumes disposal
Integral lube oil cooler
Oil drain lines and valve
Oil filter, filler and dipstick
Prelube - required with prime, continuous, and standby
Rubber anti-vibration mounts (shipped loose)
Battery disconnect switch
Batteries and battery rack w/cables
Dual 24 volt electric starting motors
Rails - Engine / generator
Two PM inspections
Busbar
Paint - Caterpillar yellow with high gloss black rails & radiator
Right hand service
Flywheel and flywheel housing-SAE No. 00
SAE standard rotation
4 x Single element canister with service indicator(s)
EMCP 4.2B
Volts (L-L & L-N)
Engine cycle crank
Power Factor (per phase & average)
Overcurrent
Communications
Emergency stop
2 Programmable relay outputs (Form C)
6 Programmable digital inputs
2 Programmable digital outputs
Environmental sealed front face.
DC Volts
Reverse power
Programmable Protective Relaying Functions
High coolant temperature
Accessory module data link
Low coolant level
Over / under frequency
Amps (per phase & average)
True RMS AC metering, 3-phase, +/-2% accuracy
Low coolant temperature
Reverse Reactive Power
Controls
Oil pressure (psi, kPa or bar)
Lamp test
Coolant temperature
Warning / shutdown Indicators
4 Programmable relay outputs (Form A)
Alarm acknowledge
Generator phase sequence
24 Volt DC operation
Serial annunciator module data link
Customer data link (Modbus RTU)
Failure to start (overcrank)
Auto / start / stop control.
Low oil pressure
RPM
Text alarm / event descriptions.
Digital Indicators
Generator mounted - rear facing
Emergency stop pushbutton
Engine cool-down timer.
Operating hours
Over / under voltage
Overspeed
Frequency (Hz)
Radiator group - shipped loose
SCAC cooling
Coolant Sensors
Coolant drain line and valves
Fan and belt guards
Bolted flange, with bellow for each turbo
Dry Exhaust Manifold
Filters x 3
Secondary / Tertiary fuel filters
10 Micron Spin On Type
4 Micron Spin On Type
Primary fuel filter water / fuel water separator
Engine mounted filters X3
6 Leads
IEC platinum stator RTDs
Voltage regulator
Reactive droop capability
3 Phase voltage sensing
RFI suppression
Min / max exciter limiter
exciter diode monitor
Form Wound
Permanent magnet
NEMA Class H insulation
Class H temperature rise at 40C ambient
(LV) Busbar connections, top/center mounted, top cable entry
3 Phase Brushless
Salient pole
50 Hz models: IEC standard hole pattern
(MV) Busbar connections, right side extension box, bottom cable entry
Anti condensation space heater
Class F temperature rise at 40C ambient
Right side extension box, bottom cable entry
ADEM A4
Redundant shutdown (Overspeed protection through a duplicate speed sensing system)
Gear type lube oil pump
Lubricating oil
Fumes disposal
Integral lube oil cooler
Oil drain lines and valve
Oil filter, filler and dipstick
Prelube - required with prime, continuous, and standby
Rubber anti-vibration mounts (shipped loose)
Battery disconnect switch
Batteries and battery rack w/cables
Dual 24 volt electric starting motors
Rails - Engine / generator
Two PM inspections
Busbar
Paint - Caterpillar yellow with high gloss black rails & radiator
Right hand service
Flywheel and flywheel housing-SAE No. 00
SAE standard rotation
4 x Single element canister with service indicator(s)
EMCP 4.2B
Volts (L-L & L-N)
Engine cycle crank
Power Factor (per phase & average)
Overcurrent
Communications
Emergency stop
2 Programmable relay outputs (Form C)
6 Programmable digital inputs
2 Programmable digital outputs
Environmental sealed front face.
DC Volts
Reverse power
Programmable Protective Relaying Functions
High coolant temperature
Accessory module data link
Low coolant level
Over / under frequency
Amps (per phase & average)
True RMS AC metering, 3-phase, +/-2% accuracy
Low coolant temperature
Reverse Reactive Power
Controls
Oil pressure (psi, kPa or bar)
Lamp test
Coolant temperature
Warning / shutdown Indicators
4 Programmable relay outputs (Form A)
Alarm acknowledge
Generator phase sequence
24 Volt DC operation
Serial annunciator module data link
Customer data link (Modbus RTU)
Failure to start (overcrank)
Auto / start / stop control.
Low oil pressure
RPM
Text alarm / event descriptions.
Digital Indicators
Generator mounted - rear facing
Emergency stop pushbutton
Engine cool-down timer.
Operating hours
Over / under voltage
Overspeed
Frequency (Hz)
Radiator group - shipped loose
SCAC cooling
Coolant Sensors
Coolant drain line and valves
Fan and belt guards
Bolted flange, with bellow for each turbo
Dry Exhaust Manifold
Filters x 3
Secondary / Tertiary fuel filters
10 Micron Spin On Type
4 Micron Spin On Type
Primary fuel filter water / fuel water separator
Engine mounted filters X3
6 Leads
IEC platinum stator RTDs
Voltage regulator
Reactive droop capability
3 Phase voltage sensing
RFI suppression
Min / max exciter limiter
exciter diode monitor
Form Wound
Permanent magnet
NEMA Class H insulation
Class H temperature rise at 40C ambient
(LV) Busbar connections, top/center mounted, top cable entry
3 Phase Brushless
Salient pole
50 Hz models: IEC standard hole pattern
(MV) Busbar connections, right side extension box, bottom cable entry
Anti condensation space heater
Class F temperature rise at 40C ambient
Right side extension box, bottom cable entry
ADEM A4
Redundant shutdown (Overspeed protection through a duplicate speed sensing system)
Gear type lube oil pump
Lubricating oil
Fumes disposal
Integral lube oil cooler
Oil drain lines and valve
Oil filter, filler and dipstick
Prelube - required with prime, continuous, and standby
Rubber anti-vibration mounts (shipped loose)
Battery disconnect switch
Batteries and battery rack w/cables
Dual 24 volt electric starting motors
Rails - Engine / generator
Two PM inspections
Busbar
Paint - Caterpillar yellow with high gloss black rails & radiator
Right hand service
Flywheel and flywheel housing-SAE No. 00
SAE standard rotation
Exhaust
Exhaust flange outlet
Exhaust flange outlet
4 x Single element canister with service indicator(s)
EMCP 4.2B
Volts (L-L & L-N)
Engine cycle crank
Power Factor (per phase & average)
Overcurrent
Communications
Emergency stop
2 Programmable relay outputs (Form C)
6 Programmable digital inputs
2 Programmable digital outputs
Environmental sealed front face.
DC Volts
Reverse power
Programmable Protective Relaying Functions
High coolant temperature
Accessory module data link
Low coolant level
Over / under frequency
Amps (per phase & average)
True RMS AC metering, 3-phase, +/-2% accuracy
Low coolant temperature
Reverse Reactive Power
Controls
Oil pressure (psi, kPa or bar)
Lamp test
Coolant temperature
Warning / shutdown Indicators
4 Programmable relay outputs (Form A)
Alarm acknowledge
Generator phase sequence
24 Volt DC operation
Serial annunciator module data link
Customer data link (Modbus RTU)
Failure to start (overcrank)
Auto / start / stop control.
Low oil pressure
RPM
Text alarm / event descriptions.
Digital Indicators
Generator mounted - rear facing
Emergency stop pushbutton
Engine cool-down timer.
Operating hours
Over / under voltage
Overspeed
Frequency (Hz)
Radiator group - shipped loose
SCAC cooling
Coolant Sensors
Coolant drain line and valves
Fan and belt guards
Bolted flange, with bellow for each turbo
Dry Exhaust Manifold
Filters x 3
Secondary / Tertiary fuel filters
10 Micron Spin On Type
4 Micron Spin On Type
Primary fuel filter water / fuel water separator
Engine mounted filters X3
6 Leads
IEC platinum stator RTDs
Voltage regulator
Reactive droop capability
3 Phase voltage sensing
RFI suppression
Min / max exciter limiter
exciter diode monitor
Form Wound
Permanent magnet
NEMA Class H insulation
Class H temperature rise at 40C ambient
(LV) Busbar connections, top/center mounted, top cable entry
3 Phase Brushless
Salient pole
50 Hz models: IEC standard hole pattern
(MV) Busbar connections, right side extension box, bottom cable entry
Anti condensation space heater
Class F temperature rise at 40C ambient
Right side extension box, bottom cable entry
ADEM A4
Redundant shutdown (Overspeed protection through a duplicate speed sensing system)
Gear type lube oil pump
Lubricating oil
Fumes disposal
Integral lube oil cooler
Oil drain lines and valve
Oil filter, filler and dipstick
Prelube - required with prime, continuous, and standby
Rubber anti-vibration mounts (shipped loose)
Battery disconnect switch
Batteries and battery rack w/cables
Dual 24 volt electric starting motors
Rails - Engine / generator
Two PM inspections
Busbar
Paint - Caterpillar yellow with high gloss black rails & radiator
Right hand service
Flywheel and flywheel housing-SAE No. 00
SAE standard rotation
4 x Single element canister with service indicator(s)
EMCP 4.2B
Volts (L-L & L-N)
Engine cycle crank
Power Factor (per phase & average)
Overcurrent
Communications
Emergency stop
2 Programmable relay outputs (Form C)
6 Programmable digital inputs
2 Programmable digital outputs
Environmental sealed front face.
DC Volts
Reverse power
Programmable Protective Relaying Functions
High coolant temperature
Accessory module data link
Low coolant level
Over / under frequency
Amps (per phase & average)
True RMS AC metering, 3-phase, +/-2% accuracy
Low coolant temperature
Reverse Reactive Power
Controls
Oil pressure (psi, kPa or bar)
Lamp test
Coolant temperature
Warning / shutdown Indicators
4 Programmable relay outputs (Form A)
Alarm acknowledge
Generator phase sequence
24 Volt DC operation
Serial annunciator module data link
Customer data link (Modbus RTU)
Failure to start (overcrank)
Auto / start / stop control.
Low oil pressure
RPM
Text alarm / event descriptions.
Digital Indicators
Generator mounted - rear facing
Emergency stop pushbutton
Engine cool-down timer.
Operating hours
Over / under voltage
Overspeed
Frequency (Hz)
Radiator group - shipped loose
SCAC cooling
Coolant Sensors
Coolant drain line and valves
Fan and belt guards
Bolted flange, with bellow for each turbo
Dry Exhaust Manifold
Filters x 3
Secondary / Tertiary fuel filters
10 Micron Spin On Type
4 Micron Spin On Type
Primary fuel filter water / fuel water separator
Engine mounted filters X3
6 Leads
IEC platinum stator RTDs
Voltage regulator
Reactive droop capability
3 Phase voltage sensing
RFI suppression
Min / max exciter limiter
exciter diode monitor
Form Wound
Permanent magnet
NEMA Class H insulation
Class H temperature rise at 40C ambient
(LV) Busbar connections, top/center mounted, top cable entry
3 Phase Brushless
Salient pole
50 Hz models: IEC standard hole pattern
(MV) Busbar connections, right side extension box, bottom cable entry
Anti condensation space heater
Class F temperature rise at 40C ambient
Right side extension box, bottom cable entry
ADEM A4
Redundant shutdown (Overspeed protection through a duplicate speed sensing system)
Gear type lube oil pump
Lubricating oil
Fumes disposal
Integral lube oil cooler
Oil drain lines and valve
Oil filter, filler and dipstick
Prelube - required with prime, continuous, and standby
Rubber anti-vibration mounts (shipped loose)
Battery disconnect switch
Batteries and battery rack w/cables
Dual 24 volt electric starting motors
Rails - Engine / generator
Two PM inspections
Busbar
Paint - Caterpillar yellow with high gloss black rails & radiator
Right hand service
Flywheel and flywheel housing-SAE No. 00
SAE standard rotation
4 x Single element canister with service indicator(s)
EMCP 4.2B
Volts (L-L & L-N)
Engine cycle crank
Power Factor (per phase & average)
Overcurrent
Communications
Emergency stop
2 Programmable relay outputs (Form C)
6 Programmable digital inputs
2 Programmable digital outputs
Environmental sealed front face.
DC Volts
Reverse power
Programmable Protective Relaying Functions
High coolant temperature
Accessory module data link
Low coolant level
Over / under frequency
Amps (per phase & average)
True RMS AC metering, 3-phase, +/-2% accuracy
Low coolant temperature
Reverse Reactive Power
Controls
Oil pressure (psi, kPa or bar)
Lamp test
Coolant temperature
Warning / shutdown Indicators
4 Programmable relay outputs (Form A)
Alarm acknowledge
Generator phase sequence
24 Volt DC operation
Serial annunciator module data link
Customer data link (Modbus RTU)
Failure to start (overcrank)
Auto / start / stop control.
Low oil pressure
RPM
Text alarm / event descriptions.
Digital Indicators
Generator mounted - rear facing
Emergency stop pushbutton
Engine cool-down timer.
Operating hours
Over / under voltage
Overspeed
Frequency (Hz)
Radiator group - shipped loose
SCAC cooling
Coolant Sensors
Coolant drain line and valves
Fan and belt guards
Bolted flange, with bellow for each turbo
Dry Exhaust Manifold
Filters x 3
Secondary / Tertiary fuel filters
10 Micron Spin On Type
4 Micron Spin On Type
Primary fuel filter water / fuel water separator
Engine mounted filters X3
6 Leads
IEC platinum stator RTDs
Voltage regulator
Reactive droop capability
3 Phase voltage sensing
RFI suppression
Min / max exciter limiter
exciter diode monitor
Form Wound
Permanent magnet
NEMA Class H insulation
Class H temperature rise at 40C ambient
(LV) Busbar connections, top/center mounted, top cable entry
3 Phase Brushless
Salient pole
50 Hz models: IEC standard hole pattern
(MV) Busbar connections, right side extension box, bottom cable entry
Anti condensation space heater
Class F temperature rise at 40C ambient
Right side extension box, bottom cable entry
ADEM A4
Redundant shutdown (Overspeed protection through a duplicate speed sensing system)
Gear type lube oil pump
Lubricating oil
Fumes disposal
Integral lube oil cooler
Oil drain lines and valve
Oil filter, filler and dipstick
Prelube - required with prime, continuous, and standby
Rubber anti-vibration mounts (shipped loose)
Battery disconnect switch
Batteries and battery rack w/cables
Dual 24 volt electric starting motors
Rails - Engine / generator
Two PM inspections
Busbar
Paint - Caterpillar yellow with high gloss black rails & radiator
Right hand service
Flywheel and flywheel housing-SAE No. 00
SAE standard rotation
Fuel
Primary fuel filter with integral water separator
Secondary fuel filter
Fuel priming pump
Primary fuel filter with integral water separator
4 x Single element canister with service indicator(s)
EMCP 4.2B
Volts (L-L & L-N)
Engine cycle crank
Power Factor (per phase & average)
Overcurrent
Communications
Emergency stop
2 Programmable relay outputs (Form C)
6 Programmable digital inputs
2 Programmable digital outputs
Environmental sealed front face.
DC Volts
Reverse power
Programmable Protective Relaying Functions
High coolant temperature
Accessory module data link
Low coolant level
Over / under frequency
Amps (per phase & average)
True RMS AC metering, 3-phase, +/-2% accuracy
Low coolant temperature
Reverse Reactive Power
Controls
Oil pressure (psi, kPa or bar)
Lamp test
Coolant temperature
Warning / shutdown Indicators
4 Programmable relay outputs (Form A)
Alarm acknowledge
Generator phase sequence
24 Volt DC operation
Serial annunciator module data link
Customer data link (Modbus RTU)
Failure to start (overcrank)
Auto / start / stop control.
Low oil pressure
RPM
Text alarm / event descriptions.
Digital Indicators
Generator mounted - rear facing
Emergency stop pushbutton
Engine cool-down timer.
Operating hours
Over / under voltage
Overspeed
Frequency (Hz)
Radiator group - shipped loose
SCAC cooling
Coolant Sensors
Coolant drain line and valves
Fan and belt guards
Bolted flange, with bellow for each turbo
Dry Exhaust Manifold
Filters x 3
Secondary / Tertiary fuel filters
10 Micron Spin On Type
4 Micron Spin On Type
Primary fuel filter water / fuel water separator
Engine mounted filters X3
6 Leads
IEC platinum stator RTDs
Voltage regulator
Reactive droop capability
3 Phase voltage sensing
RFI suppression
Min / max exciter limiter
exciter diode monitor
Form Wound
Permanent magnet
NEMA Class H insulation
Class H temperature rise at 40C ambient
(LV) Busbar connections, top/center mounted, top cable entry
3 Phase Brushless
Salient pole
50 Hz models: IEC standard hole pattern
(MV) Busbar connections, right side extension box, bottom cable entry
Anti condensation space heater
Class F temperature rise at 40C ambient
Right side extension box, bottom cable entry
ADEM A4
Redundant shutdown (Overspeed protection through a duplicate speed sensing system)
Gear type lube oil pump
Lubricating oil
Fumes disposal
Integral lube oil cooler
Oil drain lines and valve
Oil filter, filler and dipstick
Prelube - required with prime, continuous, and standby
Rubber anti-vibration mounts (shipped loose)
Battery disconnect switch
Batteries and battery rack w/cables
Dual 24 volt electric starting motors
Rails - Engine / generator
Two PM inspections
Busbar
Paint - Caterpillar yellow with high gloss black rails & radiator
Right hand service
Flywheel and flywheel housing-SAE No. 00
SAE standard rotation
4 x Single element canister with service indicator(s)
EMCP 4.2B
Volts (L-L & L-N)
Engine cycle crank
Power Factor (per phase & average)
Overcurrent
Communications
Emergency stop
2 Programmable relay outputs (Form C)
6 Programmable digital inputs
2 Programmable digital outputs
Environmental sealed front face.
DC Volts
Reverse power
Programmable Protective Relaying Functions
High coolant temperature
Accessory module data link
Low coolant level
Over / under frequency
Amps (per phase & average)
True RMS AC metering, 3-phase, +/-2% accuracy
Low coolant temperature
Reverse Reactive Power
Controls
Oil pressure (psi, kPa or bar)
Lamp test
Coolant temperature
Warning / shutdown Indicators
4 Programmable relay outputs (Form A)
Alarm acknowledge
Generator phase sequence
24 Volt DC operation
Serial annunciator module data link
Customer data link (Modbus RTU)
Failure to start (overcrank)
Auto / start / stop control.
Low oil pressure
RPM
Text alarm / event descriptions.
Digital Indicators
Generator mounted - rear facing
Emergency stop pushbutton
Engine cool-down timer.
Operating hours
Over / under voltage
Overspeed
Frequency (Hz)
Radiator group - shipped loose
SCAC cooling
Coolant Sensors
Coolant drain line and valves
Fan and belt guards
Bolted flange, with bellow for each turbo
Dry Exhaust Manifold
Filters x 3
Secondary / Tertiary fuel filters
10 Micron Spin On Type
4 Micron Spin On Type
Primary fuel filter water / fuel water separator
Engine mounted filters X3
6 Leads
IEC platinum stator RTDs
Voltage regulator
Reactive droop capability
3 Phase voltage sensing
RFI suppression
Min / max exciter limiter
exciter diode monitor
Form Wound
Permanent magnet
NEMA Class H insulation
Class H temperature rise at 40C ambient
(LV) Busbar connections, top/center mounted, top cable entry
3 Phase Brushless
Salient pole
50 Hz models: IEC standard hole pattern
(MV) Busbar connections, right side extension box, bottom cable entry
Anti condensation space heater
Class F temperature rise at 40C ambient
Right side extension box, bottom cable entry
ADEM A4
Redundant shutdown (Overspeed protection through a duplicate speed sensing system)
Gear type lube oil pump
Lubricating oil
Fumes disposal
Integral lube oil cooler
Oil drain lines and valve
Oil filter, filler and dipstick
Prelube - required with prime, continuous, and standby
Rubber anti-vibration mounts (shipped loose)
Battery disconnect switch
Batteries and battery rack w/cables
Dual 24 volt electric starting motors
Rails - Engine / generator
Two PM inspections
Busbar
Paint - Caterpillar yellow with high gloss black rails & radiator
Right hand service
Flywheel and flywheel housing-SAE No. 00
SAE standard rotation
4 x Single element canister with service indicator(s)
EMCP 4.2B
Volts (L-L & L-N)
Engine cycle crank
Power Factor (per phase & average)
Overcurrent
Communications
Emergency stop
2 Programmable relay outputs (Form C)
6 Programmable digital inputs
2 Programmable digital outputs
Environmental sealed front face.
DC Volts
Reverse power
Programmable Protective Relaying Functions
High coolant temperature
Accessory module data link
Low coolant level
Over / under frequency
Amps (per phase & average)
True RMS AC metering, 3-phase, +/-2% accuracy
Low coolant temperature
Reverse Reactive Power
Controls
Oil pressure (psi, kPa or bar)
Lamp test
Coolant temperature
Warning / shutdown Indicators
4 Programmable relay outputs (Form A)
Alarm acknowledge
Generator phase sequence
24 Volt DC operation
Serial annunciator module data link
Customer data link (Modbus RTU)
Failure to start (overcrank)
Auto / start / stop control.
Low oil pressure
RPM
Text alarm / event descriptions.
Digital Indicators
Generator mounted - rear facing
Emergency stop pushbutton
Engine cool-down timer.
Operating hours
Over / under voltage
Overspeed
Frequency (Hz)
Radiator group - shipped loose
SCAC cooling
Coolant Sensors
Coolant drain line and valves
Fan and belt guards
Bolted flange, with bellow for each turbo
Dry Exhaust Manifold
Filters x 3
Secondary / Tertiary fuel filters
10 Micron Spin On Type
4 Micron Spin On Type
Primary fuel filter water / fuel water separator
Engine mounted filters X3
6 Leads
IEC platinum stator RTDs
Voltage regulator
Reactive droop capability
3 Phase voltage sensing
RFI suppression
Min / max exciter limiter
exciter diode monitor
Form Wound
Permanent magnet
NEMA Class H insulation
Class H temperature rise at 40C ambient
(LV) Busbar connections, top/center mounted, top cable entry
3 Phase Brushless
Salient pole
50 Hz models: IEC standard hole pattern
(MV) Busbar connections, right side extension box, bottom cable entry
Anti condensation space heater
Class F temperature rise at 40C ambient
Right side extension box, bottom cable entry
ADEM A4
Redundant shutdown (Overspeed protection through a duplicate speed sensing system)
Gear type lube oil pump
Lubricating oil
Fumes disposal
Integral lube oil cooler
Oil drain lines and valve
Oil filter, filler and dipstick
Prelube - required with prime, continuous, and standby
Rubber anti-vibration mounts (shipped loose)
Battery disconnect switch
Batteries and battery rack w/cables
Dual 24 volt electric starting motors
Rails - Engine / generator
Two PM inspections
Busbar
Paint - Caterpillar yellow with high gloss black rails & radiator
Right hand service
Flywheel and flywheel housing-SAE No. 00
SAE standard rotation
Secondary fuel filter
4 x Single element canister with service indicator(s)
EMCP 4.2B
Volts (L-L & L-N)
Engine cycle crank
Power Factor (per phase & average)
Overcurrent
Communications
Emergency stop
2 Programmable relay outputs (Form C)
6 Programmable digital inputs
2 Programmable digital outputs
Environmental sealed front face.
DC Volts
Reverse power
Programmable Protective Relaying Functions
High coolant temperature
Accessory module data link
Low coolant level
Over / under frequency
Amps (per phase & average)
True RMS AC metering, 3-phase, +/-2% accuracy
Low coolant temperature
Reverse Reactive Power
Controls
Oil pressure (psi, kPa or bar)
Lamp test
Coolant temperature
Warning / shutdown Indicators
4 Programmable relay outputs (Form A)
Alarm acknowledge
Generator phase sequence
24 Volt DC operation
Serial annunciator module data link
Customer data link (Modbus RTU)
Failure to start (overcrank)
Auto / start / stop control.
Low oil pressure
RPM
Text alarm / event descriptions.
Digital Indicators
Generator mounted - rear facing
Emergency stop pushbutton
Engine cool-down timer.
Operating hours
Over / under voltage
Overspeed
Frequency (Hz)
Radiator group - shipped loose
SCAC cooling
Coolant Sensors
Coolant drain line and valves
Fan and belt guards
Bolted flange, with bellow for each turbo
Dry Exhaust Manifold
Filters x 3
Secondary / Tertiary fuel filters
10 Micron Spin On Type
4 Micron Spin On Type
Primary fuel filter water / fuel water separator
Engine mounted filters X3
6 Leads
IEC platinum stator RTDs
Voltage regulator
Reactive droop capability
3 Phase voltage sensing
RFI suppression
Min / max exciter limiter
exciter diode monitor
Form Wound
Permanent magnet
NEMA Class H insulation
Class H temperature rise at 40C ambient
(LV) Busbar connections, top/center mounted, top cable entry
3 Phase Brushless
Salient pole
50 Hz models: IEC standard hole pattern
(MV) Busbar connections, right side extension box, bottom cable entry
Anti condensation space heater
Class F temperature rise at 40C ambient
Right side extension box, bottom cable entry
ADEM A4
Redundant shutdown (Overspeed protection through a duplicate speed sensing system)
Gear type lube oil pump
Lubricating oil
Fumes disposal
Integral lube oil cooler
Oil drain lines and valve
Oil filter, filler and dipstick
Prelube - required with prime, continuous, and standby
Rubber anti-vibration mounts (shipped loose)
Battery disconnect switch
Batteries and battery rack w/cables
Dual 24 volt electric starting motors
Rails - Engine / generator
Two PM inspections
Busbar
Paint - Caterpillar yellow with high gloss black rails & radiator
Right hand service
Flywheel and flywheel housing-SAE No. 00
SAE standard rotation
4 x Single element canister with service indicator(s)
EMCP 4.2B
Volts (L-L & L-N)
Engine cycle crank
Power Factor (per phase & average)
Overcurrent
Communications
Emergency stop
2 Programmable relay outputs (Form C)
6 Programmable digital inputs
2 Programmable digital outputs
Environmental sealed front face.
DC Volts
Reverse power
Programmable Protective Relaying Functions
High coolant temperature
Accessory module data link
Low coolant level
Over / under frequency
Amps (per phase & average)
True RMS AC metering, 3-phase, +/-2% accuracy
Low coolant temperature
Reverse Reactive Power
Controls
Oil pressure (psi, kPa or bar)
Lamp test
Coolant temperature
Warning / shutdown Indicators
4 Programmable relay outputs (Form A)
Alarm acknowledge
Generator phase sequence
24 Volt DC operation
Serial annunciator module data link
Customer data link (Modbus RTU)
Failure to start (overcrank)
Auto / start / stop control.
Low oil pressure
RPM
Text alarm / event descriptions.
Digital Indicators
Generator mounted - rear facing
Emergency stop pushbutton
Engine cool-down timer.
Operating hours
Over / under voltage
Overspeed
Frequency (Hz)
Radiator group - shipped loose
SCAC cooling
Coolant Sensors
Coolant drain line and valves
Fan and belt guards
Bolted flange, with bellow for each turbo
Dry Exhaust Manifold
Filters x 3
Secondary / Tertiary fuel filters
10 Micron Spin On Type
4 Micron Spin On Type
Primary fuel filter water / fuel water separator
Engine mounted filters X3
6 Leads
IEC platinum stator RTDs
Voltage regulator
Reactive droop capability
3 Phase voltage sensing
RFI suppression
Min / max exciter limiter
exciter diode monitor
Form Wound
Permanent magnet
NEMA Class H insulation
Class H temperature rise at 40C ambient
(LV) Busbar connections, top/center mounted, top cable entry
3 Phase Brushless
Salient pole
50 Hz models: IEC standard hole pattern
(MV) Busbar connections, right side extension box, bottom cable entry
Anti condensation space heater
Class F temperature rise at 40C ambient
Right side extension box, bottom cable entry
ADEM A4
Redundant shutdown (Overspeed protection through a duplicate speed sensing system)
Gear type lube oil pump
Lubricating oil
Fumes disposal
Integral lube oil cooler
Oil drain lines and valve
Oil filter, filler and dipstick
Prelube - required with prime, continuous, and standby
Rubber anti-vibration mounts (shipped loose)
Battery disconnect switch
Batteries and battery rack w/cables
Dual 24 volt electric starting motors
Rails - Engine / generator
Two PM inspections
Busbar
Paint - Caterpillar yellow with high gloss black rails & radiator
Right hand service
Flywheel and flywheel housing-SAE No. 00
SAE standard rotation
4 x Single element canister with service indicator(s)
EMCP 4.2B
Volts (L-L & L-N)
Engine cycle crank
Power Factor (per phase & average)
Overcurrent
Communications
Emergency stop
2 Programmable relay outputs (Form C)
6 Programmable digital inputs
2 Programmable digital outputs
Environmental sealed front face.
DC Volts
Reverse power
Programmable Protective Relaying Functions
High coolant temperature
Accessory module data link
Low coolant level
Over / under frequency
Amps (per phase & average)
True RMS AC metering, 3-phase, +/-2% accuracy
Low coolant temperature
Reverse Reactive Power
Controls
Oil pressure (psi, kPa or bar)
Lamp test
Coolant temperature
Warning / shutdown Indicators
4 Programmable relay outputs (Form A)
Alarm acknowledge
Generator phase sequence
24 Volt DC operation
Serial annunciator module data link
Customer data link (Modbus RTU)
Failure to start (overcrank)
Auto / start / stop control.
Low oil pressure
RPM
Text alarm / event descriptions.
Digital Indicators
Generator mounted - rear facing
Emergency stop pushbutton
Engine cool-down timer.
Operating hours
Over / under voltage
Overspeed
Frequency (Hz)
Radiator group - shipped loose
SCAC cooling
Coolant Sensors
Coolant drain line and valves
Fan and belt guards
Bolted flange, with bellow for each turbo
Dry Exhaust Manifold
Filters x 3
Secondary / Tertiary fuel filters
10 Micron Spin On Type
4 Micron Spin On Type
Primary fuel filter water / fuel water separator
Engine mounted filters X3
6 Leads
IEC platinum stator RTDs
Voltage regulator
Reactive droop capability
3 Phase voltage sensing
RFI suppression
Min / max exciter limiter
exciter diode monitor
Form Wound
Permanent magnet
NEMA Class H insulation
Class H temperature rise at 40C ambient
(LV) Busbar connections, top/center mounted, top cable entry
3 Phase Brushless
Salient pole
50 Hz models: IEC standard hole pattern
(MV) Busbar connections, right side extension box, bottom cable entry
Anti condensation space heater
Class F temperature rise at 40C ambient
Right side extension box, bottom cable entry
ADEM A4
Redundant shutdown (Overspeed protection through a duplicate speed sensing system)
Gear type lube oil pump
Lubricating oil
Fumes disposal
Integral lube oil cooler
Oil drain lines and valve
Oil filter, filler and dipstick
Prelube - required with prime, continuous, and standby
Rubber anti-vibration mounts (shipped loose)
Battery disconnect switch
Batteries and battery rack w/cables
Dual 24 volt electric starting motors
Rails - Engine / generator
Two PM inspections
Busbar
Paint - Caterpillar yellow with high gloss black rails & radiator
Right hand service
Flywheel and flywheel housing-SAE No. 00
SAE standard rotation
Fuel priming pump
4 x Single element canister with service indicator(s)
EMCP 4.2B
Volts (L-L & L-N)
Engine cycle crank
Power Factor (per phase & average)
Overcurrent
Communications
Emergency stop
2 Programmable relay outputs (Form C)
6 Programmable digital inputs
2 Programmable digital outputs
Environmental sealed front face.
DC Volts
Reverse power
Programmable Protective Relaying Functions
High coolant temperature
Accessory module data link
Low coolant level
Over / under frequency
Amps (per phase & average)
True RMS AC metering, 3-phase, +/-2% accuracy
Low coolant temperature
Reverse Reactive Power
Controls
Oil pressure (psi, kPa or bar)
Lamp test
Coolant temperature
Warning / shutdown Indicators
4 Programmable relay outputs (Form A)
Alarm acknowledge
Generator phase sequence
24 Volt DC operation
Serial annunciator module data link
Customer data link (Modbus RTU)
Failure to start (overcrank)
Auto / start / stop control.
Low oil pressure
RPM
Text alarm / event descriptions.
Digital Indicators
Generator mounted - rear facing
Emergency stop pushbutton
Engine cool-down timer.
Operating hours
Over / under voltage
Overspeed
Frequency (Hz)
Radiator group - shipped loose
SCAC cooling
Coolant Sensors
Coolant drain line and valves
Fan and belt guards
Bolted flange, with bellow for each turbo
Dry Exhaust Manifold
Filters x 3
Secondary / Tertiary fuel filters
10 Micron Spin On Type
4 Micron Spin On Type
Primary fuel filter water / fuel water separator
Engine mounted filters X3
6 Leads
IEC platinum stator RTDs
Voltage regulator
Reactive droop capability
3 Phase voltage sensing
RFI suppression
Min / max exciter limiter
exciter diode monitor
Form Wound
Permanent magnet
NEMA Class H insulation
Class H temperature rise at 40C ambient
(LV) Busbar connections, top/center mounted, top cable entry
3 Phase Brushless
Salient pole
50 Hz models: IEC standard hole pattern
(MV) Busbar connections, right side extension box, bottom cable entry
Anti condensation space heater
Class F temperature rise at 40C ambient
Right side extension box, bottom cable entry
ADEM A4
Redundant shutdown (Overspeed protection through a duplicate speed sensing system)
Gear type lube oil pump
Lubricating oil
Fumes disposal
Integral lube oil cooler
Oil drain lines and valve
Oil filter, filler and dipstick
Prelube - required with prime, continuous, and standby
Rubber anti-vibration mounts (shipped loose)
Battery disconnect switch
Batteries and battery rack w/cables
Dual 24 volt electric starting motors
Rails - Engine / generator
Two PM inspections
Busbar
Paint - Caterpillar yellow with high gloss black rails & radiator
Right hand service
Flywheel and flywheel housing-SAE No. 00
SAE standard rotation
4 x Single element canister with service indicator(s)
EMCP 4.2B
Volts (L-L & L-N)
Engine cycle crank
Power Factor (per phase & average)
Overcurrent
Communications
Emergency stop
2 Programmable relay outputs (Form C)
6 Programmable digital inputs
2 Programmable digital outputs
Environmental sealed front face.
DC Volts
Reverse power
Programmable Protective Relaying Functions
High coolant temperature
Accessory module data link
Low coolant level
Over / under frequency
Amps (per phase & average)
True RMS AC metering, 3-phase, +/-2% accuracy
Low coolant temperature
Reverse Reactive Power
Controls
Oil pressure (psi, kPa or bar)
Lamp test
Coolant temperature
Warning / shutdown Indicators
4 Programmable relay outputs (Form A)
Alarm acknowledge
Generator phase sequence
24 Volt DC operation
Serial annunciator module data link
Customer data link (Modbus RTU)
Failure to start (overcrank)
Auto / start / stop control.
Low oil pressure
RPM
Text alarm / event descriptions.
Digital Indicators
Generator mounted - rear facing
Emergency stop pushbutton
Engine cool-down timer.
Operating hours
Over / under voltage
Overspeed
Frequency (Hz)
Radiator group - shipped loose
SCAC cooling
Coolant Sensors
Coolant drain line and valves
Fan and belt guards
Bolted flange, with bellow for each turbo
Dry Exhaust Manifold
Filters x 3
Secondary / Tertiary fuel filters
10 Micron Spin On Type
4 Micron Spin On Type
Primary fuel filter water / fuel water separator
Engine mounted filters X3
6 Leads
IEC platinum stator RTDs
Voltage regulator
Reactive droop capability
3 Phase voltage sensing
RFI suppression
Min / max exciter limiter
exciter diode monitor
Form Wound
Permanent magnet
NEMA Class H insulation
Class H temperature rise at 40C ambient
(LV) Busbar connections, top/center mounted, top cable entry
3 Phase Brushless
Salient pole
50 Hz models: IEC standard hole pattern
(MV) Busbar connections, right side extension box, bottom cable entry
Anti condensation space heater
Class F temperature rise at 40C ambient
Right side extension box, bottom cable entry
ADEM A4
Redundant shutdown (Overspeed protection through a duplicate speed sensing system)
Gear type lube oil pump
Lubricating oil
Fumes disposal
Integral lube oil cooler
Oil drain lines and valve
Oil filter, filler and dipstick
Prelube - required with prime, continuous, and standby
Rubber anti-vibration mounts (shipped loose)
Battery disconnect switch
Batteries and battery rack w/cables
Dual 24 volt electric starting motors
Rails - Engine / generator
Two PM inspections
Busbar
Paint - Caterpillar yellow with high gloss black rails & radiator
Right hand service
Flywheel and flywheel housing-SAE No. 00
SAE standard rotation
4 x Single element canister with service indicator(s)
EMCP 4.2B
Volts (L-L & L-N)
Engine cycle crank
Power Factor (per phase & average)
Overcurrent
Communications
Emergency stop
2 Programmable relay outputs (Form C)
6 Programmable digital inputs
2 Programmable digital outputs
Environmental sealed front face.
DC Volts
Reverse power
Programmable Protective Relaying Functions
High coolant temperature
Accessory module data link
Low coolant level
Over / under frequency
Amps (per phase & average)
True RMS AC metering, 3-phase, +/-2% accuracy
Low coolant temperature
Reverse Reactive Power
Controls
Oil pressure (psi, kPa or bar)
Lamp test
Coolant temperature
Warning / shutdown Indicators
4 Programmable relay outputs (Form A)
Alarm acknowledge
Generator phase sequence
24 Volt DC operation
Serial annunciator module data link
Customer data link (Modbus RTU)
Failure to start (overcrank)
Auto / start / stop control.
Low oil pressure
RPM
Text alarm / event descriptions.
Digital Indicators
Generator mounted - rear facing
Emergency stop pushbutton
Engine cool-down timer.
Operating hours
Over / under voltage
Overspeed
Frequency (Hz)
Radiator group - shipped loose
SCAC cooling
Coolant Sensors
Coolant drain line and valves
Fan and belt guards
Bolted flange, with bellow for each turbo
Dry Exhaust Manifold
Filters x 3
Secondary / Tertiary fuel filters
10 Micron Spin On Type
4 Micron Spin On Type
Primary fuel filter water / fuel water separator
Engine mounted filters X3
6 Leads
IEC platinum stator RTDs
Voltage regulator
Reactive droop capability
3 Phase voltage sensing
RFI suppression
Min / max exciter limiter
exciter diode monitor
Form Wound
Permanent magnet
NEMA Class H insulation
Class H temperature rise at 40C ambient
(LV) Busbar connections, top/center mounted, top cable entry
3 Phase Brushless
Salient pole
50 Hz models: IEC standard hole pattern
(MV) Busbar connections, right side extension box, bottom cable entry
Anti condensation space heater
Class F temperature rise at 40C ambient
Right side extension box, bottom cable entry
ADEM A4
Redundant shutdown (Overspeed protection through a duplicate speed sensing system)
Gear type lube oil pump
Lubricating oil
Fumes disposal
Integral lube oil cooler
Oil drain lines and valve
Oil filter, filler and dipstick
Prelube - required with prime, continuous, and standby
Rubber anti-vibration mounts (shipped loose)
Battery disconnect switch
Batteries and battery rack w/cables
Dual 24 volt electric starting motors
Rails - Engine / generator
Two PM inspections
Busbar
Paint - Caterpillar yellow with high gloss black rails & radiator
Right hand service
Flywheel and flywheel housing-SAE No. 00
SAE standard rotation
Generator
Matched to the performance and output characteristics of Cat engines
IP23 Protection
Matched to the performance and output characteristics of Cat engines
4 x Single element canister with service indicator(s)
EMCP 4.2B
Volts (L-L & L-N)
Engine cycle crank
Power Factor (per phase & average)
Overcurrent
Communications
Emergency stop
2 Programmable relay outputs (Form C)
6 Programmable digital inputs
2 Programmable digital outputs
Environmental sealed front face.
DC Volts
Reverse power
Programmable Protective Relaying Functions
High coolant temperature
Accessory module data link
Low coolant level
Over / under frequency
Amps (per phase & average)
True RMS AC metering, 3-phase, +/-2% accuracy
Low coolant temperature
Reverse Reactive Power
Controls
Oil pressure (psi, kPa or bar)
Lamp test
Coolant temperature
Warning / shutdown Indicators
4 Programmable relay outputs (Form A)
Alarm acknowledge
Generator phase sequence
24 Volt DC operation
Serial annunciator module data link
Customer data link (Modbus RTU)
Failure to start (overcrank)
Auto / start / stop control.
Low oil pressure
RPM
Text alarm / event descriptions.
Digital Indicators
Generator mounted - rear facing
Emergency stop pushbutton
Engine cool-down timer.
Operating hours
Over / under voltage
Overspeed
Frequency (Hz)
Radiator group - shipped loose
SCAC cooling
Coolant Sensors
Coolant drain line and valves
Fan and belt guards
Bolted flange, with bellow for each turbo
Dry Exhaust Manifold
Filters x 3
Secondary / Tertiary fuel filters
10 Micron Spin On Type
4 Micron Spin On Type
Primary fuel filter water / fuel water separator
Engine mounted filters X3
6 Leads
IEC platinum stator RTDs
Voltage regulator
Reactive droop capability
3 Phase voltage sensing
RFI suppression
Min / max exciter limiter
exciter diode monitor
Form Wound
Permanent magnet
NEMA Class H insulation
Class H temperature rise at 40C ambient
(LV) Busbar connections, top/center mounted, top cable entry
3 Phase Brushless
Salient pole
50 Hz models: IEC standard hole pattern
(MV) Busbar connections, right side extension box, bottom cable entry
Anti condensation space heater
Class F temperature rise at 40C ambient
Right side extension box, bottom cable entry
ADEM A4
Redundant shutdown (Overspeed protection through a duplicate speed sensing system)
Gear type lube oil pump
Lubricating oil
Fumes disposal
Integral lube oil cooler
Oil drain lines and valve
Oil filter, filler and dipstick
Prelube - required with prime, continuous, and standby
Rubber anti-vibration mounts (shipped loose)
Battery disconnect switch
Batteries and battery rack w/cables
Dual 24 volt electric starting motors
Rails - Engine / generator
Two PM inspections
Busbar
Paint - Caterpillar yellow with high gloss black rails & radiator
Right hand service
Flywheel and flywheel housing-SAE No. 00
SAE standard rotation
4 x Single element canister with service indicator(s)
EMCP 4.2B
Volts (L-L & L-N)
Engine cycle crank
Power Factor (per phase & average)
Overcurrent
Communications
Emergency stop
2 Programmable relay outputs (Form C)
6 Programmable digital inputs
2 Programmable digital outputs
Environmental sealed front face.
DC Volts
Reverse power
Programmable Protective Relaying Functions
High coolant temperature
Accessory module data link
Low coolant level
Over / under frequency
Amps (per phase & average)
True RMS AC metering, 3-phase, +/-2% accuracy
Low coolant temperature
Reverse Reactive Power
Controls
Oil pressure (psi, kPa or bar)
Lamp test
Coolant temperature
Warning / shutdown Indicators
4 Programmable relay outputs (Form A)
Alarm acknowledge
Generator phase sequence
24 Volt DC operation
Serial annunciator module data link
Customer data link (Modbus RTU)
Failure to start (overcrank)
Auto / start / stop control.
Low oil pressure
RPM
Text alarm / event descriptions.
Digital Indicators
Generator mounted - rear facing
Emergency stop pushbutton
Engine cool-down timer.
Operating hours
Over / under voltage
Overspeed
Frequency (Hz)
Radiator group - shipped loose
SCAC cooling
Coolant Sensors
Coolant drain line and valves
Fan and belt guards
Bolted flange, with bellow for each turbo
Dry Exhaust Manifold
Filters x 3
Secondary / Tertiary fuel filters
10 Micron Spin On Type
4 Micron Spin On Type
Primary fuel filter water / fuel water separator
Engine mounted filters X3
6 Leads
IEC platinum stator RTDs
Voltage regulator
Reactive droop capability
3 Phase voltage sensing
RFI suppression
Min / max exciter limiter
exciter diode monitor
Form Wound
Permanent magnet
NEMA Class H insulation
Class H temperature rise at 40C ambient
(LV) Busbar connections, top/center mounted, top cable entry
3 Phase Brushless
Salient pole
50 Hz models: IEC standard hole pattern
(MV) Busbar connections, right side extension box, bottom cable entry
Anti condensation space heater
Class F temperature rise at 40C ambient
Right side extension box, bottom cable entry
ADEM A4
Redundant shutdown (Overspeed protection through a duplicate speed sensing system)
Gear type lube oil pump
Lubricating oil
Fumes disposal
Integral lube oil cooler
Oil drain lines and valve
Oil filter, filler and dipstick
Prelube - required with prime, continuous, and standby
Rubber anti-vibration mounts (shipped loose)
Battery disconnect switch
Batteries and battery rack w/cables
Dual 24 volt electric starting motors
Rails - Engine / generator
Two PM inspections
Busbar
Paint - Caterpillar yellow with high gloss black rails & radiator
Right hand service
Flywheel and flywheel housing-SAE No. 00
SAE standard rotation
4 x Single element canister with service indicator(s)
EMCP 4.2B
Volts (L-L & L-N)
Engine cycle crank
Power Factor (per phase & average)
Overcurrent
Communications
Emergency stop
2 Programmable relay outputs (Form C)
6 Programmable digital inputs
2 Programmable digital outputs
Environmental sealed front face.
DC Volts
Reverse power
Programmable Protective Relaying Functions
High coolant temperature
Accessory module data link
Low coolant level
Over / under frequency
Amps (per phase & average)
True RMS AC metering, 3-phase, +/-2% accuracy
Low coolant temperature
Reverse Reactive Power
Controls
Oil pressure (psi, kPa or bar)
Lamp test
Coolant temperature
Warning / shutdown Indicators
4 Programmable relay outputs (Form A)
Alarm acknowledge
Generator phase sequence
24 Volt DC operation
Serial annunciator module data link
Customer data link (Modbus RTU)
Failure to start (overcrank)
Auto / start / stop control.
Low oil pressure
RPM
Text alarm / event descriptions.
Digital Indicators
Generator mounted - rear facing
Emergency stop pushbutton
Engine cool-down timer.
Operating hours
Over / under voltage
Overspeed
Frequency (Hz)
Radiator group - shipped loose
SCAC cooling
Coolant Sensors
Coolant drain line and valves
Fan and belt guards
Bolted flange, with bellow for each turbo
Dry Exhaust Manifold
Filters x 3
Secondary / Tertiary fuel filters
10 Micron Spin On Type
4 Micron Spin On Type
Primary fuel filter water / fuel water separator
Engine mounted filters X3
6 Leads
IEC platinum stator RTDs
Voltage regulator
Reactive droop capability
3 Phase voltage sensing
RFI suppression
Min / max exciter limiter
exciter diode monitor
Form Wound
Permanent magnet
NEMA Class H insulation
Class H temperature rise at 40C ambient
(LV) Busbar connections, top/center mounted, top cable entry
3 Phase Brushless
Salient pole
50 Hz models: IEC standard hole pattern
(MV) Busbar connections, right side extension box, bottom cable entry
Anti condensation space heater
Class F temperature rise at 40C ambient
Right side extension box, bottom cable entry
ADEM A4
Redundant shutdown (Overspeed protection through a duplicate speed sensing system)
Gear type lube oil pump
Lubricating oil
Fumes disposal
Integral lube oil cooler
Oil drain lines and valve
Oil filter, filler and dipstick
Prelube - required with prime, continuous, and standby
Rubber anti-vibration mounts (shipped loose)
Battery disconnect switch
Batteries and battery rack w/cables
Dual 24 volt electric starting motors
Rails - Engine / generator
Two PM inspections
Busbar
Paint - Caterpillar yellow with high gloss black rails & radiator
Right hand service
Flywheel and flywheel housing-SAE No. 00
SAE standard rotation
IP23 Protection
4 x Single element canister with service indicator(s)
EMCP 4.2B
Volts (L-L & L-N)
Engine cycle crank
Power Factor (per phase & average)
Overcurrent
Communications
Emergency stop
2 Programmable relay outputs (Form C)
6 Programmable digital inputs
2 Programmable digital outputs
Environmental sealed front face.
DC Volts
Reverse power
Programmable Protective Relaying Functions
High coolant temperature
Accessory module data link
Low coolant level
Over / under frequency
Amps (per phase & average)
True RMS AC metering, 3-phase, +/-2% accuracy
Low coolant temperature
Reverse Reactive Power
Controls
Oil pressure (psi, kPa or bar)
Lamp test
Coolant temperature
Warning / shutdown Indicators
4 Programmable relay outputs (Form A)
Alarm acknowledge
Generator phase sequence
24 Volt DC operation
Serial annunciator module data link
Customer data link (Modbus RTU)
Failure to start (overcrank)
Auto / start / stop control.
Low oil pressure
RPM
Text alarm / event descriptions.
Digital Indicators
Generator mounted - rear facing
Emergency stop pushbutton
Engine cool-down timer.
Operating hours
Over / under voltage
Overspeed
Frequency (Hz)
Radiator group - shipped loose
SCAC cooling
Coolant Sensors
Coolant drain line and valves
Fan and belt guards
Bolted flange, with bellow for each turbo
Dry Exhaust Manifold
Filters x 3
Secondary / Tertiary fuel filters
10 Micron Spin On Type
4 Micron Spin On Type
Primary fuel filter water / fuel water separator
Engine mounted filters X3
6 Leads
IEC platinum stator RTDs
Voltage regulator
Reactive droop capability
3 Phase voltage sensing
RFI suppression
Min / max exciter limiter
exciter diode monitor
Form Wound
Permanent magnet
NEMA Class H insulation
Class H temperature rise at 40C ambient
(LV) Busbar connections, top/center mounted, top cable entry
3 Phase Brushless
Salient pole
50 Hz models: IEC standard hole pattern
(MV) Busbar connections, right side extension box, bottom cable entry
Anti condensation space heater
Class F temperature rise at 40C ambient
Right side extension box, bottom cable entry
ADEM A4
Redundant shutdown (Overspeed protection through a duplicate speed sensing system)
Gear type lube oil pump
Lubricating oil
Fumes disposal
Integral lube oil cooler
Oil drain lines and valve
Oil filter, filler and dipstick
Prelube - required with prime, continuous, and standby
Rubber anti-vibration mounts (shipped loose)
Battery disconnect switch
Batteries and battery rack w/cables
Dual 24 volt electric starting motors
Rails - Engine / generator
Two PM inspections
Busbar
Paint - Caterpillar yellow with high gloss black rails & radiator
Right hand service
Flywheel and flywheel housing-SAE No. 00
SAE standard rotation
4 x Single element canister with service indicator(s)
EMCP 4.2B
Volts (L-L & L-N)
Engine cycle crank
Power Factor (per phase & average)
Overcurrent
Communications
Emergency stop
2 Programmable relay outputs (Form C)
6 Programmable digital inputs
2 Programmable digital outputs
Environmental sealed front face.
DC Volts
Reverse power
Programmable Protective Relaying Functions
High coolant temperature
Accessory module data link
Low coolant level
Over / under frequency
Amps (per phase & average)
True RMS AC metering, 3-phase, +/-2% accuracy
Low coolant temperature
Reverse Reactive Power
Controls
Oil pressure (psi, kPa or bar)
Lamp test
Coolant temperature
Warning / shutdown Indicators
4 Programmable relay outputs (Form A)
Alarm acknowledge
Generator phase sequence
24 Volt DC operation
Serial annunciator module data link
Customer data link (Modbus RTU)
Failure to start (overcrank)
Auto / start / stop control.
Low oil pressure
RPM
Text alarm / event descriptions.
Digital Indicators
Generator mounted - rear facing
Emergency stop pushbutton
Engine cool-down timer.
Operating hours
Over / under voltage
Overspeed
Frequency (Hz)
Radiator group - shipped loose
SCAC cooling
Coolant Sensors
Coolant drain line and valves
Fan and belt guards
Bolted flange, with bellow for each turbo
Dry Exhaust Manifold
Filters x 3
Secondary / Tertiary fuel filters
10 Micron Spin On Type
4 Micron Spin On Type
Primary fuel filter water / fuel water separator
Engine mounted filters X3
6 Leads
IEC platinum stator RTDs
Voltage regulator
Reactive droop capability
3 Phase voltage sensing
RFI suppression
Min / max exciter limiter
exciter diode monitor
Form Wound
Permanent magnet
NEMA Class H insulation
Class H temperature rise at 40C ambient
(LV) Busbar connections, top/center mounted, top cable entry
3 Phase Brushless
Salient pole
50 Hz models: IEC standard hole pattern
(MV) Busbar connections, right side extension box, bottom cable entry
Anti condensation space heater
Class F temperature rise at 40C ambient
Right side extension box, bottom cable entry
ADEM A4
Redundant shutdown (Overspeed protection through a duplicate speed sensing system)
Gear type lube oil pump
Lubricating oil
Fumes disposal
Integral lube oil cooler
Oil drain lines and valve
Oil filter, filler and dipstick
Prelube - required with prime, continuous, and standby
Rubber anti-vibration mounts (shipped loose)
Battery disconnect switch
Batteries and battery rack w/cables
Dual 24 volt electric starting motors
Rails - Engine / generator
Two PM inspections
Busbar
Paint - Caterpillar yellow with high gloss black rails & radiator
Right hand service
Flywheel and flywheel housing-SAE No. 00
SAE standard rotation
4 x Single element canister with service indicator(s)
EMCP 4.2B
Volts (L-L & L-N)
Engine cycle crank
Power Factor (per phase & average)
Overcurrent
Communications
Emergency stop
2 Programmable relay outputs (Form C)
6 Programmable digital inputs
2 Programmable digital outputs
Environmental sealed front face.
DC Volts
Reverse power
Programmable Protective Relaying Functions
High coolant temperature
Accessory module data link
Low coolant level
Over / under frequency
Amps (per phase & average)
True RMS AC metering, 3-phase, +/-2% accuracy
Low coolant temperature
Reverse Reactive Power
Controls
Oil pressure (psi, kPa or bar)
Lamp test
Coolant temperature
Warning / shutdown Indicators
4 Programmable relay outputs (Form A)
Alarm acknowledge
Generator phase sequence
24 Volt DC operation
Serial annunciator module data link
Customer data link (Modbus RTU)
Failure to start (overcrank)
Auto / start / stop control.
Low oil pressure
RPM
Text alarm / event descriptions.
Digital Indicators
Generator mounted - rear facing
Emergency stop pushbutton
Engine cool-down timer.
Operating hours
Over / under voltage
Overspeed
Frequency (Hz)
Radiator group - shipped loose
SCAC cooling
Coolant Sensors
Coolant drain line and valves
Fan and belt guards
Bolted flange, with bellow for each turbo
Dry Exhaust Manifold
Filters x 3
Secondary / Tertiary fuel filters
10 Micron Spin On Type
4 Micron Spin On Type
Primary fuel filter water / fuel water separator
Engine mounted filters X3
6 Leads
IEC platinum stator RTDs
Voltage regulator
Reactive droop capability
3 Phase voltage sensing
RFI suppression
Min / max exciter limiter
exciter diode monitor
Form Wound
Permanent magnet
NEMA Class H insulation
Class H temperature rise at 40C ambient
(LV) Busbar connections, top/center mounted, top cable entry
3 Phase Brushless
Salient pole
50 Hz models: IEC standard hole pattern
(MV) Busbar connections, right side extension box, bottom cable entry
Anti condensation space heater
Class F temperature rise at 40C ambient
Right side extension box, bottom cable entry
ADEM A4
Redundant shutdown (Overspeed protection through a duplicate speed sensing system)
Gear type lube oil pump
Lubricating oil
Fumes disposal
Integral lube oil cooler
Oil drain lines and valve
Oil filter, filler and dipstick
Prelube - required with prime, continuous, and standby
Rubber anti-vibration mounts (shipped loose)
Battery disconnect switch
Batteries and battery rack w/cables
Dual 24 volt electric starting motors
Rails - Engine / generator
Two PM inspections
Busbar
Paint - Caterpillar yellow with high gloss black rails & radiator
Right hand service
Flywheel and flywheel housing-SAE No. 00
SAE standard rotation
Power Termination
Bus Bar
Control Panel
EMCP 4 Genset Controller
EMCP 4 Genset Controller
4 x Single element canister with service indicator(s)
EMCP 4.2B
Volts (L-L & L-N)
Engine cycle crank
Power Factor (per phase & average)
Overcurrent
Communications
Emergency stop
2 Programmable relay outputs (Form C)
6 Programmable digital inputs
2 Programmable digital outputs
Environmental sealed front face.
DC Volts
Reverse power
Programmable Protective Relaying Functions
High coolant temperature
Accessory module data link
Low coolant level
Over / under frequency
Amps (per phase & average)
True RMS AC metering, 3-phase, +/-2% accuracy
Low coolant temperature
Reverse Reactive Power
Controls
Oil pressure (psi, kPa or bar)
Lamp test
Coolant temperature
Warning / shutdown Indicators
4 Programmable relay outputs (Form A)
Alarm acknowledge
Generator phase sequence
24 Volt DC operation
Serial annunciator module data link
Customer data link (Modbus RTU)
Failure to start (overcrank)
Auto / start / stop control.
Low oil pressure
RPM
Text alarm / event descriptions.
Digital Indicators
Generator mounted - rear facing
Emergency stop pushbutton
Engine cool-down timer.
Operating hours
Over / under voltage
Overspeed
Frequency (Hz)
Radiator group - shipped loose
SCAC cooling
Coolant Sensors
Coolant drain line and valves
Fan and belt guards
Bolted flange, with bellow for each turbo
Dry Exhaust Manifold
Filters x 3
Secondary / Tertiary fuel filters
10 Micron Spin On Type
4 Micron Spin On Type
Primary fuel filter water / fuel water separator
Engine mounted filters X3
6 Leads
IEC platinum stator RTDs
Voltage regulator
Reactive droop capability
3 Phase voltage sensing
RFI suppression
Min / max exciter limiter
exciter diode monitor
Form Wound
Permanent magnet
NEMA Class H insulation
Class H temperature rise at 40C ambient
(LV) Busbar connections, top/center mounted, top cable entry
3 Phase Brushless
Salient pole
50 Hz models: IEC standard hole pattern
(MV) Busbar connections, right side extension box, bottom cable entry
Anti condensation space heater
Class F temperature rise at 40C ambient
Right side extension box, bottom cable entry
ADEM A4
Redundant shutdown (Overspeed protection through a duplicate speed sensing system)
Gear type lube oil pump
Lubricating oil
Fumes disposal
Integral lube oil cooler
Oil drain lines and valve
Oil filter, filler and dipstick
Prelube - required with prime, continuous, and standby
Rubber anti-vibration mounts (shipped loose)
Battery disconnect switch
Batteries and battery rack w/cables
Dual 24 volt electric starting motors
Rails - Engine / generator
Two PM inspections
Busbar
Paint - Caterpillar yellow with high gloss black rails & radiator
Right hand service
Flywheel and flywheel housing-SAE No. 00
SAE standard rotation
4 x Single element canister with service indicator(s)
EMCP 4.2B
Volts (L-L & L-N)
Engine cycle crank
Power Factor (per phase & average)
Overcurrent
Communications
Emergency stop
2 Programmable relay outputs (Form C)
6 Programmable digital inputs
2 Programmable digital outputs
Environmental sealed front face.
DC Volts
Reverse power
Programmable Protective Relaying Functions
High coolant temperature
Accessory module data link
Low coolant level
Over / under frequency
Amps (per phase & average)
True RMS AC metering, 3-phase, +/-2% accuracy
Low coolant temperature
Reverse Reactive Power
Controls
Oil pressure (psi, kPa or bar)
Lamp test
Coolant temperature
Warning / shutdown Indicators
4 Programmable relay outputs (Form A)
Alarm acknowledge
Generator phase sequence
24 Volt DC operation
Serial annunciator module data link
Customer data link (Modbus RTU)
Failure to start (overcrank)
Auto / start / stop control.
Low oil pressure
RPM
Text alarm / event descriptions.
Digital Indicators
Generator mounted - rear facing
Emergency stop pushbutton
Engine cool-down timer.
Operating hours
Over / under voltage
Overspeed
Frequency (Hz)
Radiator group - shipped loose
SCAC cooling
Coolant Sensors
Coolant drain line and valves
Fan and belt guards
Bolted flange, with bellow for each turbo
Dry Exhaust Manifold
Filters x 3
Secondary / Tertiary fuel filters
10 Micron Spin On Type
4 Micron Spin On Type
Primary fuel filter water / fuel water separator
Engine mounted filters X3
6 Leads
IEC platinum stator RTDs
Voltage regulator
Reactive droop capability
3 Phase voltage sensing
RFI suppression
Min / max exciter limiter
exciter diode monitor
Form Wound
Permanent magnet
NEMA Class H insulation
Class H temperature rise at 40C ambient
(LV) Busbar connections, top/center mounted, top cable entry
3 Phase Brushless
Salient pole
50 Hz models: IEC standard hole pattern
(MV) Busbar connections, right side extension box, bottom cable entry
Anti condensation space heater
Class F temperature rise at 40C ambient
Right side extension box, bottom cable entry
ADEM A4
Redundant shutdown (Overspeed protection through a duplicate speed sensing system)
Gear type lube oil pump
Lubricating oil
Fumes disposal
Integral lube oil cooler
Oil drain lines and valve
Oil filter, filler and dipstick
Prelube - required with prime, continuous, and standby
Rubber anti-vibration mounts (shipped loose)
Battery disconnect switch
Batteries and battery rack w/cables
Dual 24 volt electric starting motors
Rails - Engine / generator
Two PM inspections
Busbar
Paint - Caterpillar yellow with high gloss black rails & radiator
Right hand service
Flywheel and flywheel housing-SAE No. 00
SAE standard rotation
4 x Single element canister with service indicator(s)
EMCP 4.2B
Volts (L-L & L-N)
Engine cycle crank
Power Factor (per phase & average)
Overcurrent
Communications
Emergency stop
2 Programmable relay outputs (Form C)
6 Programmable digital inputs
2 Programmable digital outputs
Environmental sealed front face.
DC Volts
Reverse power
Programmable Protective Relaying Functions
High coolant temperature
Accessory module data link
Low coolant level
Over / under frequency
Amps (per phase & average)
True RMS AC metering, 3-phase, +/-2% accuracy
Low coolant temperature
Reverse Reactive Power
Controls
Oil pressure (psi, kPa or bar)
Lamp test
Coolant temperature
Warning / shutdown Indicators
4 Programmable relay outputs (Form A)
Alarm acknowledge
Generator phase sequence
24 Volt DC operation
Serial annunciator module data link
Customer data link (Modbus RTU)
Failure to start (overcrank)
Auto / start / stop control.
Low oil pressure
RPM
Text alarm / event descriptions.
Digital Indicators
Generator mounted - rear facing
Emergency stop pushbutton
Engine cool-down timer.
Operating hours
Over / under voltage
Overspeed
Frequency (Hz)
Radiator group - shipped loose
SCAC cooling
Coolant Sensors
Coolant drain line and valves
Fan and belt guards
Bolted flange, with bellow for each turbo
Dry Exhaust Manifold
Filters x 3
Secondary / Tertiary fuel filters
10 Micron Spin On Type
4 Micron Spin On Type
Primary fuel filter water / fuel water separator
Engine mounted filters X3
6 Leads
IEC platinum stator RTDs
Voltage regulator
Reactive droop capability
3 Phase voltage sensing
RFI suppression
Min / max exciter limiter
exciter diode monitor
Form Wound
Permanent magnet
NEMA Class H insulation
Class H temperature rise at 40C ambient
(LV) Busbar connections, top/center mounted, top cable entry
3 Phase Brushless
Salient pole
50 Hz models: IEC standard hole pattern
(MV) Busbar connections, right side extension box, bottom cable entry
Anti condensation space heater
Class F temperature rise at 40C ambient
Right side extension box, bottom cable entry
ADEM A4
Redundant shutdown (Overspeed protection through a duplicate speed sensing system)
Gear type lube oil pump
Lubricating oil
Fumes disposal
Integral lube oil cooler
Oil drain lines and valve
Oil filter, filler and dipstick
Prelube - required with prime, continuous, and standby
Rubber anti-vibration mounts (shipped loose)
Battery disconnect switch
Batteries and battery rack w/cables
Dual 24 volt electric starting motors
Rails - Engine / generator
Two PM inspections
Busbar
Paint - Caterpillar yellow with high gloss black rails & radiator
Right hand service
Flywheel and flywheel housing-SAE No. 00
SAE standard rotation
General
Paint - Caterpillar Yellow except rails and radiators gloss black
Air Inlet System
4 x Single element canister with service indicator(s)
Control Panel
EMCP 4.2B
Volts (L-L & L-N)
Engine cycle crank
Power Factor (per phase & average)
Overcurrent
Communications
Emergency stop
2 Programmable relay outputs (Form C)
6 Programmable digital inputs
2 Programmable digital outputs
Environmental sealed front face.
DC Volts
Reverse power
Programmable Protective Relaying Functions
High coolant temperature
Accessory module data link
Low coolant level
Over / under frequency
Amps (per phase & average)
True RMS AC metering, 3-phase, +/-2% accuracy
Low coolant temperature
Reverse Reactive Power
Controls
Oil pressure (psi, kPa or bar)
Lamp test
Coolant temperature
Warning / shutdown Indicators
4 Programmable relay outputs (Form A)
Alarm acknowledge
Generator phase sequence
24 Volt DC operation
Serial annunciator module data link
Customer data link (Modbus RTU)
Failure to start (overcrank)
Auto / start / stop control.
Low oil pressure
RPM
Text alarm / event descriptions.
Digital Indicators
Generator mounted - rear facing
Emergency stop pushbutton
Engine cool-down timer.
Operating hours
Over / under voltage
Overspeed
Frequency (Hz)
Cooling System
Radiator group - shipped loose
SCAC cooling
Coolant Sensors
Coolant drain line and valves
Fan and belt guards
Exhaust System
Bolted flange, with bellow for each turbo
Dry Exhaust Manifold
Fuel System
Filters x 3
Secondary / Tertiary fuel filters
10 Micron Spin On Type
4 Micron Spin On Type
Primary fuel filter water / fuel water separator
Engine mounted filters X3
Generator and Attachments
6 Leads
IEC platinum stator RTDs
Voltage regulator
Reactive droop capability
3 Phase voltage sensing
RFI suppression
Min / max exciter limiter
exciter diode monitor
Form Wound
Permanent magnet
NEMA Class H insulation
Class H temperature rise at 40C ambient
(LV) Busbar connections, top/center mounted, top cable entry
3 Phase Brushless
Salient pole
50 Hz models: IEC standard hole pattern
(MV) Busbar connections, right side extension box, bottom cable entry
Anti condensation space heater
Class F temperature rise at 40C ambient
Right side extension box, bottom cable entry
Governing System
ADEM A4
Redundant shutdown (Overspeed protection through a duplicate speed sensing system)
Lube System
Gear type lube oil pump
Lubricating oil
Fumes disposal
Integral lube oil cooler
Oil drain lines and valve
Oil filter, filler and dipstick
Prelube - required with prime, continuous, and standby
Mounting Systems
Rubber anti-vibration mounts (shipped loose)
Battery disconnect switch
Batteries and battery rack w/cables
Dual 24 volt electric starting motors
Rails - Engine / generator
Service Instructions
Two PM inspections
Power Termination
Busbar
General
Paint - Caterpillar yellow with high gloss black rails & radiator
Right hand service
Flywheel and flywheel housing-SAE No. 00
SAE standard rotation
Air Inlet System
4 x Single element canister with service indicator(s)
Control Panel
EMCP 4.2B
Volts (L-L & L-N)
Engine cycle crank
Power Factor (per phase & average)
Overcurrent
Communications
Emergency stop
2 Programmable relay outputs (Form C)
6 Programmable digital inputs
2 Programmable digital outputs
Environmental sealed front face.
DC Volts
Reverse power
Programmable Protective Relaying Functions
High coolant temperature
Accessory module data link
Low coolant level
Over / under frequency
Amps (per phase & average)
True RMS AC metering, 3-phase, +/-2% accuracy
Low coolant temperature
Reverse Reactive Power
Controls
Oil pressure (psi, kPa or bar)
Lamp test
Coolant temperature
Warning / shutdown Indicators
4 Programmable relay outputs (Form A)
Alarm acknowledge
Generator phase sequence
24 Volt DC operation
Serial annunciator module data link
Customer data link (Modbus RTU)
Failure to start (overcrank)
Auto / start / stop control.
Low oil pressure
RPM
Text alarm / event descriptions.
Digital Indicators
Generator mounted - rear facing
Emergency stop pushbutton
Engine cool-down timer.
Operating hours
Over / under voltage
Overspeed
Frequency (Hz)
Cooling System
Radiator group - shipped loose
SCAC cooling
Coolant Sensors
Coolant drain line and valves
Fan and belt guards
Exhaust System
Bolted flange, with bellow for each turbo
Dry Exhaust Manifold
Fuel System
Filters x 3
Secondary / Tertiary fuel filters
10 Micron Spin On Type
4 Micron Spin On Type
Primary fuel filter water / fuel water separator
Engine mounted filters X3
Generator and Attachments
6 Leads
IEC platinum stator RTDs
Voltage regulator
Reactive droop capability
3 Phase voltage sensing
RFI suppression
Min / max exciter limiter
exciter diode monitor
Form Wound
Permanent magnet
NEMA Class H insulation
Class H temperature rise at 40C ambient
(LV) Busbar connections, top/center mounted, top cable entry
3 Phase Brushless
Salient pole
50 Hz models: IEC standard hole pattern
(MV) Busbar connections, right side extension box, bottom cable entry
Anti condensation space heater
Class F temperature rise at 40C ambient
Right side extension box, bottom cable entry
Governing System
ADEM A4
Redundant shutdown (Overspeed protection through a duplicate speed sensing system)
Lube System
Gear type lube oil pump
Lubricating oil
Fumes disposal
Integral lube oil cooler
Oil drain lines and valve
Oil filter, filler and dipstick
Prelube - required with prime, continuous, and standby
Mounting Systems
Rubber anti-vibration mounts (shipped loose)
Battery disconnect switch
Batteries and battery rack w/cables
Dual 24 volt electric starting motors
Rails - Engine / generator
Service Instructions
Two PM inspections
Power Termination
Busbar
General
Paint - Caterpillar yellow with high gloss black rails & radiator
Right hand service
Flywheel and flywheel housing-SAE No. 00
SAE standard rotation
Air Inlet System
4 x Single element canister with service indicator(s)
Control Panel
EMCP 4.2B
Volts (L-L & L-N)
Engine cycle crank
Power Factor (per phase & average)
Overcurrent
Communications
Emergency stop
2 Programmable relay outputs (Form C)
6 Programmable digital inputs
2 Programmable digital outputs
Environmental sealed front face.
DC Volts
Reverse power
Programmable Protective Relaying Functions
High coolant temperature
Accessory module data link
Low coolant level
Over / under frequency
Amps (per phase & average)
True RMS AC metering, 3-phase, +/-2% accuracy
Low coolant temperature
Reverse Reactive Power
Controls
Oil pressure (psi, kPa or bar)
Lamp test
Coolant temperature
Warning / shutdown Indicators
4 Programmable relay outputs (Form A)
Alarm acknowledge
Generator phase sequence
24 Volt DC operation
Serial annunciator module data link
Customer data link (Modbus RTU)
Failure to start (overcrank)
Auto / start / stop control.
Low oil pressure
RPM
Text alarm / event descriptions.
Digital Indicators
Generator mounted - rear facing
Emergency stop pushbutton
Engine cool-down timer.
Operating hours
Over / under voltage
Overspeed
Frequency (Hz)
Cooling System
Radiator group - shipped loose
SCAC cooling
Coolant Sensors
Coolant drain line and valves
Fan and belt guards
Exhaust System
Bolted flange, with bellow for each turbo
Dry Exhaust Manifold
Fuel System
Filters x 3
Secondary / Tertiary fuel filters
10 Micron Spin On Type
4 Micron Spin On Type
Primary fuel filter water / fuel water separator
Engine mounted filters X3
Generator and Attachments
6 Leads
IEC platinum stator RTDs
Voltage regulator
Reactive droop capability
3 Phase voltage sensing
RFI suppression
Min / max exciter limiter
exciter diode monitor
Form Wound
Permanent magnet
NEMA Class H insulation
Class H temperature rise at 40C ambient
(LV) Busbar connections, top/center mounted, top cable entry
3 Phase Brushless
Salient pole
50 Hz models: IEC standard hole pattern
(MV) Busbar connections, right side extension box, bottom cable entry
Anti condensation space heater
Class F temperature rise at 40C ambient
Right side extension box, bottom cable entry
Governing System
ADEM A4
Redundant shutdown (Overspeed protection through a duplicate speed sensing system)
Lube System
Gear type lube oil pump
Lubricating oil
Fumes disposal
Integral lube oil cooler
Oil drain lines and valve
Oil filter, filler and dipstick
Prelube - required with prime, continuous, and standby
Mounting Systems
Rubber anti-vibration mounts (shipped loose)
Battery disconnect switch
Batteries and battery rack w/cables
Dual 24 volt electric starting motors
Rails - Engine / generator
Service Instructions
Two PM inspections
Power Termination
Busbar
General
Paint - Caterpillar yellow with high gloss black rails & radiator
Right hand service
Flywheel and flywheel housing-SAE No. 00
SAE standard rotation
Exhaust
Exhaust mufflers <!--(except Tier 4)-->
Generator
Anti-condensation heater
Internal excitation (IE)
Permanent magnet excitation (PMG)
Oversize and premium generators
Anti-condensation heater
Internal excitation (IE)
Permanent magnet excitation (PMG)
Oversize and premium generators
Power Termination
Circuit breakers, UL listed
Circuit breakers, IEC compliant
Circuit breakers, UL listed
Circuit breakers, IEC compliant
Control Panels
EMCP 4.2
EMCP 4.3
EMCP 4.4
Generator temperature monitoring & protection
Load share module
Digital I/O module
Remote monitoring software
EMCP 4.2
EMCP 4.3
EMCP 4.4
Generator temperature monitoring & protection
Load share module
Digital I/O module
Remote monitoring software
Mounting
Rubber anti-vibration mounts
Spring-type vibration isolator
IBC isolators
Starting/Charging
Battery chargers
Oversize batteries
Jacket water heater
Heavy-duty starting system
Charging alternator
Air starting motor with control and silencer
General
The following options are based on regional and product configuration:
Seismic Certification per applicable building codes: IBC 2000, IBC 2003, IBC 2006, IBC 2009, CBC 2007
UL 2200 package
EU Certificate of Conformance (CE)
CSA Certification
EEC Declaration of Conformity
Enclosures: sound attenuated, weather protective
Automatic transfer switches (ATS)
Integral & sub-base fuel tanks
Integral & sub-base UL listed dual wall fuel tanks
30 Mins