C27 ACERT Land Mechanical Drilling Engine
Land Mechanical Engines
-
Specification Summary
- Maximum Rating 858 bkW
- Emissions U.S. EPA Non-road Tier 2
- Displacement 27.2 l
- Minimum Rating 597 bkW
- Download Brochure
Engine Specifications
| Maximum Rating | 858 bkW |
| Emissions | U.S. EPA Non-road Tier 2 |
| Displacement | 27.2 l |
| Minimum Rating | 597 bkW |
| Bore | 137.7 mm |
| Stroke | 152.4 mm |
| Rated Speed | 1800 r/min |
| Aspiration | Turbocharged-Aftercooled |
| Governor and Protection | ADEM A3 |
| Engine Weight - Net Dry | 2895 kg |
| Oil Change Interval | 250 |
| Rotation from Flywheel End | Counterclockwise |
| Flywheel and Flywheel Housing | SAE No. 0 or SAE No. 1 |
| Flywheel Teeth | 136 (SAE 0), 113 (SAE 1) |
Capacity for Liquids
| Minimum Cooling System - Engine Only | 54.9 l |
Dimensions
| Length | 1918 mm |
| Width | 1463 mm |
| Height | 1321 mm |
Air Inlet System
Dual turbochargers side or rear mounted — inlet 152.4 mm (6 in.) hose connection
Dual turbochargers side or rear mounted — inlet 152.4 mm (6 in.) hose connection
Control System
Electronic governing, PTO speed control
Programmable ratings
Cold mode start strategy
Automatic altitude compensation
Power compensation for fuel temperature
Programmable low and high idle and TEL
Electronic diagnostics and fault logging
Engine monitoring and protection system (speed, temperature, pressure)
J1939 Broadcast (diagnostic, engine status, and control)
Cooling System
Thermostats and housing — outlet LH vertical orientation
Jacket water pump — gear-driven, centrifugal RH
Thermostats and housing — outlet LH vertical orientation
Jacket water pump — gear-driven, centrifugal RH
Exhaust System
Exhaust manifold — dry, heat shields
Dual turbo — rear turbo exhaust, full marmon connection 127 mm (5 in.), maximum load 10 kg for direct
Water-cooled center sections
Flywheels and Flywheel Housings
SAE No. 0 or SAE No. 1
SAE standard rotation
SAE No. 0 or SAE No. 1
SAE standard rotation
Fuel System
MEUI system
Fuel filter, RH ( 2 micron high performance)
Fuel transfer pump
Fuel priming pump (optional electric priming pump)
Lube System
Crankcase breather — rear mounted
Oil cooler — RH
Side turbo — oil filler in RH front gear case
Rear turbo — oil filler in RH valve cover
Oil level gauge — RH
Oil filter — RH
Oil pan rear sump
Mounting System
Front support — narrow
Front support — narrow
Power Take-Offs
Crankshaft pulley — 203.2 mm (8 in), 5 grooves 15.9 mm (.63 in) wide; 292.1 mm (11.5 in.) 1 groove 15.9 mm (.63 in.) wide
General
Vibration damper
Paint — Cat yellow
Lifting eyes
Automatic variable timing, electronic
Electronic installation kit 70-pin connector (connectors, pins, sockets)
Air Inlet System
Air lines
Air cleaners
Precleaners
Air lines
Air cleaners
Precleaners
Charging System
Battery chargers
Charging alternators
Alternator mountings
Battery chargers
Charging alternators
Alternator mountings
Circuit Breakers
Circuit breaker mounting
Cooling System
Blower fans
Suction fans
Radiators
Blower fans
Suction fans
Radiators
Exhaust System
Muffler
Muffler
Flywheel and Flywheel Housings
Fuel Systems
Electric fuel priming pump
Electric fuel priming pump
Instrumentation
Gauges and instrument panels
Lube System
Lubricating oil
Oil pan
Oil filter
Mounting System
Engine supports
Engine supports
Power Take-Offs
Hydraulic pump drives
Pulley
Auxiliary drive
Hydraulic pump drives
Pulley
Auxiliary drive
Starting System
Electric starting motor
Battery sets - 24V
Battery cable
Battery rack
Starting aids
Electric starting motor
Battery sets - 24V
Battery cable
Battery rack
Starting aids
Packaging
Overseas preservation
Storage preservation
Export packaging
30 Mins