C18 ACERT Land Drilling Engine
Land Mechanical Engines
-
Specification Summary
- Maximum Rating 597 bkW
- Emissions EPA and CARB Non-Road Mobile Tier 3, EU Stage IIIA
- Displacement 18 l
- Minimum Rating 429 bkW
- Download Brochure
Engine Specifications
| Maximum Rating | 597 bkW |
| Emissions | EPA and CARB Non-Road Mobile Tier 3, EU Stage IIIA |
| Displacement | 18 l |
| Minimum Rating | 429 bkW |
| Bore | 145 mm |
| Stroke | 183 mm |
| Rated Speed | 2100 r/min |
| Aspiration | Turbocharged-Aftercooled |
| Governor and Protection | ADEM A3 |
| Engine Weight - Net Dry | 1273 kg |
| Rotation from Flywheel End | Counterclockwise |
| Oil Change Interval | 250 |
| Flywheel and Flywheel Housing | SAE No. 0 or SAE No. 1 |
| Flywheel Teeth | 136 (SAE 0), 113 (SAE 1) |
Capacity for Liquids
| Minimum Cooling System - Engine Only | 50 l |
Dimensions
| Length | 1377 mm |
| Width | 927 mm |
| Height | 1227 mm |
Air Inlet System
Single turbocharger, mid-mounted, inlet 152.4 mm (6 in), hoseconnection
Dual turbocharger, front and rear inlet 127.0 mm (5 in.), hoseconnection
Single turbocharger, mid-mounted, inlet 152.4 mm (6 in), hoseconnection
Dual turbocharger, front and rear inlet 127.0 mm (5 in.), hoseconnection
Control System
Electronic governing, PTO speed control
Programmable ratings
Cold mode start strategy
Automatic altitude compensation
Power compensation for fuel temperature
Programmable low and high idle and TEL
Electronic diagnostics and fault logging
Engine monitoring and protection system (speed, temperature,pressure)
J1939 Broadcast (diagnostic, engine status, and control)
Electronic governing, PTO speed control
Programmable ratings
Cold mode start strategy
Automatic altitude compensation
Power compensation for fuel temperature
Programmable low and high idle and TEL
Electronic diagnostics and fault logging
Engine monitoring and protection system (speed, temperature,pressure)
J1939 Broadcast (diagnostic, engine status, and control)
Cooling System
Thermostats and housing — outlet vertical
Jacket water pump — gear-driven, centrifuga
RH front water pump inlet
All plugs/fittings are STOR for lines gp water
Exhaust System
Exhaust manifold — dry
Single turbo — front-facing turbo exhaust, full marmonconnection, maximum load 10 kg for direct connection to turbo
Dual turbo — exhaust elbow, dry 203 mm (8 in)
Exhaust manifold — dry
Single turbo — front-facing turbo exhaust, full marmonconnection, maximum load 10 kg for direct connection to turbo
Dual turbo — exhaust elbow, dry 203 mm (8 in)
Flywheels and Flywheel Housings
See Mandatory Options
Fuel System
Electronic unit injector
Fuel filter, secondary, mid-mount (LH 2 micron high performance)
Fuel transfer pump, LH front
Fuel priming pump, LH mid-mount
Fuel sample valve, mounted on fuel filter base.
Electronic unit injector
Fuel filter, secondary, mid-mount (LH 2 micron high performance)
Fuel transfer pump, LH front
Fuel priming pump, LH mid-mount
Fuel sample valve, mounted on fuel filter base.
Lube System
Crankcase breather — rear valve cover
Oil cooler — RH (dual)
Oil filter — RH, LH
Oil pan — front sump
Oil dipstick — LH front
Oil pump
Crankcase breather — rear valve cover
Oil cooler — RH (dual)
Oil filter — RH, LH
Oil pan — front sump
Oil dipstick — LH front
Oil pump
Mounting System
Front support (shipping only)
Power Take-Offs
Crankshaft pulley, 203.2 mm (8 in), 3 grooves 292.1 mm(11.5 in) 1 groove, all 15.9 mm (.63 in) width
Hydraulic pump drive, SAE A, 11-tooth
Crankshaft pulley, 203.2 mm (8 in), 3 grooves 292.1 mm(11.5 in) 1 groove, all 15.9 mm (.63 in) width
Hydraulic pump drive, SAE A, 11-tooth
General
Vibration damper
Paint — Cat yellow
Lifting eyes
Automatic variable timing, electronic
Electronic installation kit 70-pin connector (connectors, pins,sockets)
Mandatory Options
Throttle position sensor
Single turbo only — exhaust system (front or rear)
Flywheel housing or rear PTO
Primary filter/water separator
Air Compressor
Air compressor governor
Expansion chambers
Air Inlet System
Air cleaners
Air lines
Charging System
Charging alternators
Alternator mountings
Alternator wiring
Circuit breakers and mountings
Alternator belt guard
Cooling System
Radiator
Fan drive with radiator packages
Fan height instructions
Vee belts
Aftercooler lines with Caterpillar installed radiator
Single turbo configuration rear-facing exhaust
Single turbo configuration rear-facing exhaust
Aftercoooler lines
Suction fan adapters
Blower fan adapter
Blower fan
Suction fan
Fan belt
Coolant level sensor
Dry charge coolant conditioners
Exhaust System
Turbo exhaust connection
Flexible fittings
Elbows, flange, clamp, pipes
Exhaust adapters
Manifold
Mufflers
Fuel Systems
Flexible fuel lines
Fuel filter location
Fuel cooler
Water separator
Flexible fuel lines
Fuel filter location
Fuel cooler
Water separator
Instrumentation
Gauges and instrument panels
Gauges and instrument panels
Lube System
Oil pans
Drain and cover
Oil level gauge
Remote oil filters
Oil filters
Lubricating oils
Oil pans
Drain and cover
Oil level gauge
Remote oil filters
Oil filters
Lubricating oils
Mounting System
Structural steel base
Front and rear engine support
Power Take-Offs
Rear enclosed clutches
Hydraulic pump drives
Hydraulics gear pumps
Clutch supports
Crankshaft pulleys
Protection System
Air shutoff
Starting System
Air starting motors
Air pressure regulator
Air silencer
Start switch
Electric starting motors — 12V, 24V
Battery sets – 24V
Battery cable and rack
Starting aids
Air starting motors
Air pressure regulator
Air silencer
Start switch
Electric starting motors — 12V, 24V
Battery sets – 24V
Battery cable and rack
Starting aids
Transmission Arrangement
Transmission water lines
30 Mins