Cat C32 ACERT Generator Set (IMO II)

Generator Set Specifications

Engine Specifications

Generator Set Dimensions

Generator Specifications

AIR INLET SYSTEM

 Separate circuit after-cooled (SCAC)

 Turbocharger, jacket water cooled

 Turbocharger inlet, 152 mm (6 in) OD straight connection

Separate circuit after-cooled (SCAC)

Turbocharger, jacket water cooled

Turbocharger inlet, 152 mm (6 in) OD straight connection

CONTROL SYSTEM

 If an EMCP panel or MGCP option is not chosen as optional equipment, then start/stop controls must be provided by the customer

 Electronic diagnostics and fault logging

 Engine Protection Mode for extended ambient conditions

 Electronic fuel/air ratio control

COOLING SYSTEM

 Separate Circuit After-Cooling (SCAC) for Heat Exchanged (HEX) & Keel cooled engines

 Jacket Water (JW) and SCAC Heat Exchangers Shell & Tube for HEX cooled engines

 SCAC pump, gear driven

 Jacket water pump, gear driven

 Sea water pump, bronze impeller, gear driven, for HEX cooled engines only

 Jacket water HEX with Sea water pump Connections: 76.2 mm (3in) ID Standard

 4 Bolt ANSI Flange Connection

 Jacket water HEX without Sea water pump Connection: 2.5" hose barb connection (inlet), 76.2 mm (3in) ID Standard 4 Bolt ANSI Flange (outlet)

 Keel Connections: 76.2 mm (3in) ID Standard 4 Bolt ANSI Flange Connection

 SCAC and JW shunt tanks for maintaining proper Pump inlet pressures

EXHAUST SYSTEM

 Water-cooled exhaust manifold & turbocharger

 4 Bolt 130 mm (5.12 in) diameter flanged outlet

Water-cooled exhaust manifold & turbocharger

4 Bolt 130 mm (5.12 in) diameter flanged outlet

FLYWHEELS & FLYWHEEL HOUSINGS

 Flywheel Housing, SAE No. 0

 Flywheel, 18 inch, 136 teeth

 SAE standard rotation

FUEL SYSTEM

 Duplex Fuel Filters, Spin-on, RH service

 Fuel connections size: Supply JIC Deg -10 (7/8 - 14), Return JIC 37 Deg -8 (3/4 -16)

 Plate-type fuel cooler installed behind Aftercooler Shunt Tank

 Fuel transfer pump, gear driven

 Manual fuel priming pump

GENERATORS AND GENERATOR ATTACHMENTS

 SR5 form wound

 2 roller bearings

 Permanent magnet excitation

 4 pole, 6 leads, Series Star connected

 Caterpillar's Digital Voltage Regulator (CDVR)

 Marine Class H insulation, Class F temperature rise

 Surface mounted platinum (PT100) 3-wire RTDs, 2 per phase on stator and one each on support bearings

 Anti-condensation space heaters (2 elements - 240 VAC, 1000 Watts

 IP23 Protection suitable for use with Fixed Water Based Local Application Fire Fighting Systems (FWBLAFFS)

 System IV insulation for harsh environment protection

LUBE SYSTEM

 Simplex oil filters, RH service

 Deep sump oil pan

 RH service oil filler locations

 RH service dipstick

 Oil pump, gear driven

MOUNTING SYSTEM

 Formed C-channel rails, 300mm (11.81in) height

 Six shipped loose combined helical spring/rubber isolators for installation below package base

GENERAL

 Front damper guard

 Common electrical bonding point on HEX and KEEL cooled engines

Front damper guard

Common electrical bonding point on HEX and KEEL cooled engines

Alarm and Protection

 Remote Panels

 MCS Controller

 Power analyzer module

 oil level, exhaust temperature, air starting pressure, heat exchanger pressure sensors

EXHAUST SYSTEM

 Dry Elbows

 Flexible Fitting

 Flange

 Muffler

 Muffler Spark Arresting

 Rain Cap

Dry Elbows

Flexible Fitting

Flange

Muffler

Muffler Spark Arresting

Rain Cap

AIR INLET SYSTEM

 Air Inlet Cleaner

 Closed Crankcase Ventilation

 Air inlet adapter

CHARGING SYSTEM

 Battery Chargers, Charging Alternators

CONTROL SYSTEM

 Load Sharing Attachment

FUEL SYSTEM

 Water Separator

LUBE SYSTEM

 Duplex Oil Filters, Sump Pump

Duplex Oil Filters, Sump Pump

PROTECTION SYSTEM

 Fuel and Oil Shielding

Fuel and Oil Shielding

STARTING SYSTEM

 Electric Starting Motors - Single 24 Volt

 Air Starting Motor

 Dual Starting Motors (Electric and Air)

 Air Start Accessories

 Starting Aids - JW Heaters

 Battery Sets - 24 Volt - Dry