Power Range | 775-1100 bhp (578-820 bkW) |
Speed Range | 1200-1600 rpm |
Emissions | IMO II, EU IW |
Aspiration | TTA |
Bore | 170 mm |
Stroke | 190 mm |
Displacement | 34.5 l |
Rotation from Flywheel End | Counterclockwise or Clockwise |
Configuration | Vee 8, 4-Stroke-Cycle Diesel |
Minimum Dry Weight | 4960 kg |
Length | 2117 mm |
Height | 1829 mm |
Width | 1703 mm |
Fuel filter, RH, with service indicators.
Fuel transfer pump.
Electronically controlled init injectors
Graphical Unit (Marine Power Display) for analog or digital display of
Crankcase breather, Top mounted
Oil filter, RH, with service indicators
Oil filler and dipstick, RH
Standard sump oil pan (500 Hour oil change interval)
Oil pump, gear type
Rails, engine mounting, ledge type, 203 mm x 203 mm (8 in x 8 in)
Accessory drive
Front housing, two-sided
A4 ECU Electronic Monitoring System provides customer programmable engine de-rate strategies to protect against adverse operating conditions
Vibration damper and guard
Lifting eyes
Paint, Caterpillar Yellow engine with black rails
NOTE: Engines for heat exchanger cooling do NOT include heat exchanger.
Flywheel, SAE No. 0, 151 teeth.
Flywheel housing, SAE No. 0.
Separate circuit aftercooler core, corrosion resistant coated (air side)
Air cleaner, regular duty
Dual turbochargers, 152 mm (6 in) OD straight connection
Dual Caterpillar A-III Electronic Engine Control, LH with Electronic Unit Injector Fuel System
Rigid Wiring Harness (10 amp DC power required to drive Electronic Engine Control Module)
Oil cooler
Thermostats and housing, Full open temperature 92 C (198 F)
Jacket water pump, gear driven, centrifugal
Auxiliary fresh water pump with SCAC engines
Auxiliary sea water pump, Centrifugal, Non-self-priming
Expansion tank
Dry gas tight exhaust manifolds with heat shields.
Dual turbochargers with watercooled bearings and heat shield.
Exhaust outlet, vertical, 203 mm (8 in) round flanged.
AIII Electronic Monitoring System provides customer programmable engine de-ration strategies to protect against adverse operating conditions
Emergency stop push button (located in Electronic Instrument Panel) Safety shutoff protection:
Battery Charger, 10 amp
Charging Alternators
Water Level Switch Gauge
Coolant Level Sensors
Connections
Keel Cooling Conversions
Heat Exchangers
Auxiliary Water Pumps
Sea Water Pump Removal
Coolant Shunt Tanks
Air Separator
Marine Gear Cooling
PL1000T Communication Module
Customer Interface
Thermocouples
Remote Panel Display
Remote Cylinder Temperature Display
Pilot House Instrument Panels
Marine Gear Sensors
Engine Vision Display System
Engine Supports
Vibration Isolators
Front Housing Accessories
Flexible Coupling and Guards
Upper Left Hand Front Location:
Upper Right Hand Front Location:
Upper Right Hand Rear Location:
Lower Left Hand Front Location:
Lower Left Hand Rear Location:
Front Housing Accessory Drives
Upper LH Accessory Drive
Upper RH Accessory Drive
Front Power Take Offs
Crankshaft Pulleys
Damper Guard Removals
Remote Air Inlet Adapters
Throttle Position Sensor
Throttle Position Signal Conv.
Throttle Position Sensor Removal
Local Speed Throttle Control
Throttle Synchronization
Exhaust Outlet
Flexible Fittings
Elbows
Flanges
Flange and Exhaust Expanders
Mufflers
Oil Pan
Oil Pan Accessories
Sump Pumps
Lubricating Oil
Air Inlet Shutoffs
Switches and Contactors
Explosion Relief Valve
Sensors
Special Appearance Packages with Chrome Covers
Chrome Plated Relief Valves
Black Air Cleaners
Yacht Class Finish
Starting Motors or Barring Device
Air Starting Motor Options:
Starting Aids
Battery Sets - 24 Volt - Dry
Battery rack
Tool set
Caterpillar datalink wire
Shrink Wrap Protection
Storage Preservation with Glycol Solution/Vapor Corrosion Inhibitor
Storage Preservation with Vapor Corrosion Inhibitor
Export Packaging